AVSPARE.COM
parts catalog

CONTROL GP-ELECTROHYDRAULIC 2270959 - Caterpillar


2270959 CONTROL GP-ELECTROHYDRAULIC Caterpillar parts 992G, 992K
Rating:
24
Alternative (cross code) number:
CA2270959
227-0959
2270959
Caterpillar 2270959 CONTROL GP-ELECTROHYDRAULIC

Buy CONTROL GP-ELECTROHYDRAULIC 2270959 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 2270959:

WHEEL LOADER  992G   992K   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:


Illustration 1 g01394327
Typical schematic
Illustration 2 g01302383
P1 ECM connector (P1-34) J1939 data link − (P1-50) J1939 data link +
Illustration 3 g01394325
Service tool connector (Terminal F) J1939 data link − (Terminal G) J1939 data link +Test Step 1. Inspect Electrical Connectors and Wiring
Remove power from the ECM.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Inspect all of the connectors that are associated with the circuit.Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Perform the following repair:Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Refer to Troubleshooting, "Electrical Connectors - Inspect".Verify that the repair eliminates the problem.STOPTest Step 2. Verify the Proper Installation of the Data Link Circuit
Disconnect any module that is connected to the CAN data link.
Disconnect J1/P1 ECM connector and measure the resistance between P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -).Expected Result:The resistance is between 57 and 63 Ohms.Results:
OK - The resistance is within the range. Proceed to Test

Caterpillar parts catalog:

Caterpillar parts catalog
992G Wheel Loader AZX00001-UP (MACHINE) POWERED BY 3508B Engine
992K Wheel Loader H4C00001-UP (MACHINE) POWERED BY C32 Engine


Parts control Caterpillar catalog:

1729389 CONTROL GP-UNPROGRAMMED
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 24H, 525B, 535B, 545, 561N, 572R...
2622876 CONTROL GP-ENGINE ELECTRONIC
854K, 992K, 993K, C13, C27, C32, D10T
2851133 CONTROL GP-UNPROGRAMMED
120K, 120K 2, 120M, 120M 2, 12K, 12M, 12M 2, 140K, 140K 2, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 16M, 2384C, 2470C, 2484C, 24M, 2570C, 2670C, 2864C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2...
3722901 CONTROL GP-ELECTRONIC
773F, 844H, 854K, 990H, 992K, 993K, C27, C32
1384670 CONTROL & MTG GP-AUX FLOW
320B, 320B L, 322B L, 325B L, 330B L
1919018 CONTROL GP-STEERING
TH62, TH63, TH82, TH83
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.