AVSPARE.COM
parts catalog

CONTROL AR-BLADE 2389466 - Caterpillar



2389466 CONTROL AR-BLADE Caterpillar parts 312C CONTROL
Rating:
14
Alternative (cross code) number:
CA2389466
238-9466
2389466
Caterpillar 2389466 CONTROL AR-BLADE

Buy CONTROL AR-BLADE 2389466 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2389466:

EXCAVATOR  312C   Caterpillar
  For full view, you need register

Information:

Removal Procedure
Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic Pressure System - Release".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines and on all cylinders for installation purposes. Plug all lines. This will help to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00592904
Start the machine and position the stick in a vertical position, as shown above.
Illustration 2 g00573878
Disconnect lines (1) and (2) .
Illustration 3 g00573882
Use the suitable lifting straps to support the stick cylinder.
Remove bolt (3) and spacer (4) .
Remove pin assembly (5) from the stick cylinder with a brass punch.
Illustration 4 g00573886
Remove bolt (6) and spacer (7) .
Remove pin assembly (8) from the stick cylinder with a brass punch.
Illustration 5 g00573896
Remove stick cylinder (9) from the stick with the suitable lifting straps. Weight of the stick cylinder is 23 kg (50 lb).Installation Procedure
Note: Be sure that the stick pin bore, boom pin bores, and stick cylinder pins are thoroughly clean prior to installation of the bucket.
Illustration 6 g00573896
Apply a thin coat of 1P-0808 Multipurpose Grease on the diameter of the pin bores and stick cylinder pins. Use the suitable lifting straps to support stick cylinder (9) into position. Weight of the stick cylinder is 23 kg (50 lb).
Illustration 7 g00573886
Install pin assembly (8) to the stick cylinder with spacer (7) and bolt (6). Tighten the bolt.
Illustration 8 g00573882
Install pin assembly (5) to the stick cylinder with spacer (4) and bolt (3). Tighten the bolt.
Illustration 9 g00573878
Connect lines (2) and (1) to the stick cylinder.

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts control Caterpillar catalog:

2427205 CONTROL GP-COMMUNICATION
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C L, 345B II, 345C, 365C, 365C L MH, 385C, 385C FS, 385C L, 561N, 572R II, 824H, 825H, 826H, 834H, 836H, 854G, 924G, 924GZ, 930G, 938G II, 950H, 953C...
1573200 CONTROL GP-IMPLEMENT
312C, 315C, 318C, 319C, 320C, 320C FM, 321C, 322C, 325C, 330C, 330C L, 345C, 345C L
2000497 CONTROL GP-JOYSTICK
312C, 315C, 318C, 319C, 320C, M325C MH
2254811 CONTROL GP-JOYSTICK
312C, 315C, 318C, 319C, 320C, 322C, 325C, 330C, 330C L
1709497 CONTROL GP-PILOT OPERATED HYD
307C, 308C, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C...
1573165 CONTROL GP-UNPROGRAMMED
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 321C, 322C, 325C, 330C, 330C FM, 330C L, 330C MH, M325C MH
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.