2792506 CONTROL GP-HANDLE Caterpillar parts
D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D8T, D9T
Rating:
Alternative (cross code) number:
CA2792506
279-2506
2792506
CA2792506
279-2506
2792506
Weight: 0.07 pounds 0 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 2792506:
Number on catalog scheme:
3
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
8S-8293 Extension 1
5P-1667 Tube 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the inside of the cylinder block is clean. Inspect the camshaft bore for metal burrs. Put a thin film of clean engine oil on the inside of the camshaft bearing bores and on each camshaft bearing prior to installation.Note: Two different camshaft bearings are used. Install the wider camshaft bearings in the front and rear camshaft bores. Install the narrow camshaft bearings in the inner bores.
Illustration 1 g00570127
Install all the camshaft bearings with Tooling (A) so that the oil hole in the camshaft bearing is in a horizontal position. Install angle (1) at 90 15 degrees.
Install the camshaft bearings with Tooling (A) on the front side of the engine. Start the bearing that is being installed from the rear of each bore. Pull the bearing into the bore with Tooling (A) . Use the following procedure for achieving the proper installation depth for the bearings.
Illustration 2 g00583232
Install the rear camshaft bearing. Pull the bearing into the bore until the front face of the bearing is flush with the front face of bore (2) .
Install the narrow internal camshaft bearings. Start at the rear of the engine and work forward. Pull each bearing into the bore until the front face of the bearing is flush with the front face of the bore.
Illustration 3 g00569930
Measure the depth of the front camshaft bearing.
Illustration 4 g00793143
Install the front camshaft bearing with Tooling (A) until the bearing is at the specified depth. The depth is measured from the front of the engine block.Note: Refer to Specifications, "Camshaft Bearings" for more information about installation depth for the remainder of the camshaft bearings.End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install".
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
8S-8293 Extension 1
5P-1667 Tube 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Ensure that the inside of the cylinder block is clean. Inspect the camshaft bore for metal burrs. Put a thin film of clean engine oil on the inside of the camshaft bearing bores and on each camshaft bearing prior to installation.Note: Two different camshaft bearings are used. Install the wider camshaft bearings in the front and rear camshaft bores. Install the narrow camshaft bearings in the inner bores.
Illustration 1 g00570127
Install all the camshaft bearings with Tooling (A) so that the oil hole in the camshaft bearing is in a horizontal position. Install angle (1) at 90 15 degrees.
Install the camshaft bearings with Tooling (A) on the front side of the engine. Start the bearing that is being installed from the rear of each bore. Pull the bearing into the bore with Tooling (A) . Use the following procedure for achieving the proper installation depth for the bearings.
Illustration 2 g00583232
Install the rear camshaft bearing. Pull the bearing into the bore until the front face of the bearing is flush with the front face of bore (2) .
Install the narrow internal camshaft bearings. Start at the rear of the engine and work forward. Pull each bearing into the bore until the front face of the bearing is flush with the front face of the bore.
Illustration 3 g00569930
Measure the depth of the front camshaft bearing.
Illustration 4 g00793143
Install the front camshaft bearing with Tooling (A) until the bearing is at the specified depth. The depth is measured from the front of the engine block.Note: Refer to Specifications, "Camshaft Bearings" for more information about installation depth for the remainder of the camshaft bearings.End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Install".
Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Cat SIS web machinery list:
Parts control Caterpillar catalog:
3238854
CONTROL GP-HANDLE
825K, D10T2, D5R LGP, D6N, D6N LGP, D6T LGP, D6T XL, D8T, D9T
825K, D10T2, D5R LGP, D6N, D6N LGP, D6T LGP, D6T XL, D8T, D9T
3740755
CONTROL GP-ELECTRONIC
12M 3 AWD, 140M 3, 160M 3, 160M 3 AWD, 336F L, 627K LRC, 725C, 966M, 966M XE, 972M, 972M XE, D6T LGP, D6T LGPPAT
12M 3 AWD, 140M 3, 160M 3, 160M 3 AWD, 336F L, 627K LRC, 725C, 966M, 966M XE, 972M, 972M XE, D6T LGP, D6T LGPPAT
525D, 535D, 545D, 555D, 621K, 623K, 623K LRC, 627K, 627K LRC, 725C, 730C, 824K, 825K, 826K, 834K, 836K, 844K, 966K, 966M, 966M XE, 972M, 972M XE, 980M, 982M, 988K, 990K, D10T2, D6T LGP, D6T LGPPAT, D9...
3861374
CONTROL GP-ELECTRONIC
D6T LGP, D6T LGPPAT
D6T LGP, D6T LGPPAT
2848906
CONTROL GP-UNPRGMED MONITOR
773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G, D10T, D11T, D8T, D9T
773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 777F, 777G, D10T, D11T, D8T, D9T
730C, 770G, 772G, D8T
3790139
CONTROL GP-ELECTRONIC
D7E, D7E LGP
D7E, D7E LGP
2865713
CONTROL GP-HANDLE
D7E, D7E LGP
D7E, D7E LGP
2865712
CONTROL GP-HANDLE
D7E, D7E LGP
D7E, D7E LGP
2865772
CONTROL GP-HANDLE
D7E, D7E LGP
D7E, D7E LGP
3292576
CONTROL GP-UNPROGRAMMED
953D, 963D, 973D, D6K, D6K LGP, D6N, PL61
953D, 963D, 973D, D6K, D6K LGP, D6N, PL61
3003631
CONTROL GP-UNPROGRAMMED
953D, 963D, D3K XL, D4K XL, D5K LGP, D6K, D6K LGP
953D, 963D, D3K XL, D4K XL, D5K LGP, D6K, D6K LGP
953D, 963D, D6K, D6K LGP, D6N, PL61
9X0438
CONTROL AS-ELECTRONIC
583T, 587T, D10N, D10R, D11N, D11R, D9N, D9R, PL83, PL87
583T, 587T, D10N, D10R, D11N, D11R, D9N, D9R, PL83, PL87
D3G, D4G, D5G
2301024
CONTROL GP-ELECTRONIC
D3G, D4G, D5G
D3G, D4G, D5G
3861374
CONTROL GP-ELECTRONIC
D6T LGP, D6T LGPPAT
D6T LGP, D6T LGPPAT
525D, 535D, 545D, 555D, 621K, 623K, 623K LRC, 627K, 627K LRC, 725C, 730C, 824K, 825K, 826K, 834K, 836K, 844K, 966K, 966M, 966M XE, 972M, 972M XE, 980M, 982M, 988K, 990K, D10T2, D6T LGP, D6T LGPPAT, D9...
3740755
CONTROL GP-ELECTRONIC
12M 3 AWD, 140M 3, 160M 3, 160M 3 AWD, 336F L, 627K LRC, 725C, 966M, 966M XE, 972M, 972M XE, D6T LGP, D6T LGPPAT
12M 3 AWD, 140M 3, 160M 3, 160M 3 AWD, 336F L, 627K LRC, 725C, 966M, 966M XE, 972M, 972M XE, D6T LGP, D6T LGPPAT
2384C, 2484C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 559C, 579C, 924K, 930K, 938K, D6K2 LGP, D6N LGP, D6N OEM
3238854
CONTROL GP-HANDLE
825K, D10T2, D5R LGP, D6N, D6N LGP, D6T LGP, D6T XL, D8T, D9T
825K, D10T2, D5R LGP, D6N, D6N LGP, D6T LGP, D6T XL, D8T, D9T
2752124
CONTROL AS
D6R III, D6T
D6R III, D6T