AVSPARE.COM
parts catalog

CONTROL & MTG GP-JOYSTICK 2809450 - Caterpillar



2809450 CONTROL & MTG GP-JOYSTICK Caterpillar parts 953D, 963D, 973D CONTROL
Rating:
68
Alternative (cross code) number:
CA2809450
280-9450
2809450
Caterpillar 2809450 CONTROL & MTG GP-JOYSTICK

Buy CONTROL & MTG GP-JOYSTICK 2809450 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compatible equipment models: 2809450:

TRACK LOADER  953D   963D   973D   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 1 g02139243
The "Hydraulic Pump 1 Outlet Pressure Sensor" is on the left side of the main control valve.
Illustration 2 g02037937
Schematic of the "Hydraulic Pump 1 Outlet Pressure Sensor"
This diagnostic code is associated with the "Hydraulic Pump 1 Outlet Pressure" Sensor. This diagnostic code is recorded when the Machine ECM reads the frequency of the signal and the frequency is not within an expected range.Note: Before performing the following procedure, ensure that the diagnostic code for this procedure is active.The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connectionsTest Step 1. CHECK THE +8 DCV SUPPLY VOLTAGE
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the sensor.
Turn the disconnect switch and the key start switch to the ON position.
At the machine harness connector for the sensor, measure the voltage (DCV) between contact 1 (wire J850-WH(White)) and contact 2 (wire 235-BK(Black)).
At the machine harness connector for the sensor, measure the voltage (DCV) between contact 1 (wire J850-WH(White)) and frame ground. Expected Result:The voltage is 8 0.5 DCV for both measurements.Results:
OK - The voltage is 8 0.5 DCV for both measurements. The voltage is correct. Proceed to Test Step 2.
NOT OK - The voltage is NOT 8 0.5 DCV for both measurements. The voltage is not correct. The Machine ECM has failed or the harness has failed.Repair: A failure of the ECM is unlikely. Verify the harness. If the harness is correct, replacement of the Machine ECM may be needed.STOPTest Step 2. VERIFY THE GROUND OF THE SENSOR
At the machine harness connector of the sensor, place a jumper between contact 2 (wire 235-BK(Black)) and frame ground.
At the machine harness connector J1, measure the resistance between the contact J1-14 (wire 235-BK(Black)) and frame ground.
At the machine harness connector J1, measure the resistance between the contact J1-2 (wire 235-BK(Black)) and frame ground. Expected Result:The resistance is less than 5 ohms for each circuit.Results:
OK - The resistance is less than 5 ohms. The circuit resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The circuit resistance is not correct. The harness is open.Repair: Repair or replace the machine harness.STOPTest Step 3. CHECK THE SENSOR SIGNAL CIRCUIT
Remove the jumper that was placed in the previous test.
At the machine harness connector of the sensor, place a jumper between contact 3 (wire K904-GN(Green)) and frame ground.
At the machine harness connector J1, measure the

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
953D TRACK-TYPE LOADER LBP00001-UP (MACHINE) POWERED BY C6.6 Engine
963D TRACK-TYPE LOADER LCS00001-UP (MACHINE) POWERED BY C6.6 Engine


Parts control Caterpillar catalog:

2399954 CONTROL GP-UNPROGRAMMED
120M, 12M, 140M, 14M, 160M, 16M, 2384C, 2484C, 312C, 312D, 315C, 318C, 319C, 319D, 320C, 320C FM, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 324D L, 3...
3074671 CONTROL GP-HANDLE
950H, 950K, 953D, 962H, 962K, 963D, 966H, 966K, 972H, 972K, 973D, 980H, 980K, 980K HLG, 986H, 988H, 992K, 993K, 994H, IT62H
2395025 CONTROL GP-UNPRGMED MONITOR
140G, 3126B, 3412E, 3606, 3608, 3612, 3616, 621B, 627F, 631D, 637D, 657E, 725, 730, 735, 740, 770, 772, 815B, 824C, 844K, 854K, 938H, 950H, 953D, 962H, 963D, 966H, 972H, 973D, 980C, 980G, 980H, 990K, ...
3722905 CONTROL GP-ELECTRONIC
120K, 12K, 12M, 140G, 140K, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 345D L, 511, 521, 521B, 522, 522B, 525C, 532, 535C, 541, 541 2, 545C, 551, 552, 552 2, 583T, ...
2863686 CONTROL GP-ENGINE ELECTRONIC
953D, 963D, D6K, D6K LGP, D6N, PL61
3003631 CONTROL GP-UNPROGRAMMED
953D, 963D, D3K XL, D4K XL, D5K LGP, D6K, D6K LGP
3292576 CONTROL GP-UNPROGRAMMED
953D, 963D, 973D, D6K, D6K LGP, D6N, PL61
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.