AVSPARE.COM
parts catalog

CONTROL & MTG GP-JOYSTICK 2809673 - Caterpillar



2809673 CONTROL & MTG GP-JOYSTICK Caterpillar parts 953D, 963D, 973D CONTROL
Rating:
69
Alternative (cross code) number:
CA2809673
280-9673
2809673
Caterpillar 2809673 CONTROL & MTG GP-JOYSTICK

Buy CONTROL & MTG GP-JOYSTICK 2809673 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compatible equipment models: 2809673:

TRACK LOADER  953D   963D   973D   Caterpillar
Number on catalog scheme: 10
 
  For full view, you need register

Information:


Illustration 1 g02139267
The "Hydraulic Pump 2 Outlet Pressure Sensor" is on the right side of the main control valve.
Illustration 2 g02038058
Schematic of the "Hydraulic Pump 2 Outlet Pressure Sensor"
This diagnostic code is associated with the "Hydraulic Pump 2 Outlet Pressure Sensor". This diagnostic code is recorded when the Machine ECM reads the sensor signal voltage and the voltage is too high.The possible causes of this diagnostic code are listed below:
The sensor has failed.
The sensor supply or the ground circuit in the machine harness is open.
The signal circuit in the machine harness is shorted to the +battery.
The signal circuit in the machine harness is open or the sensor is disconnected.
The Machine ECM has failed. Failure of the ECM is unlikely.Test Step 1. CHECK THE CONTROL AND THE HARNESS
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the machine harness from the pump pressure sensor.
At the machine harness connector for the sensor, measure the voltage (DCV) between the signal contact 3 (wire T967-YL(Yellow)) and the ground contact 2 (wire 235-BK(Black)).Expected Result:The voltage is 8.0 0.5 DCV.Results:
OK - The voltage is 8.0 0.5 DCV.Repair: The Machine ECM and the harness are correct. The sensor has failed. Replace the sensor.STOP.
NOT OK - The voltage is NOT 8.0 0.5 DCV.Repair: The Machine ECM or the harness has failed.Proceed to Test Step 2.Test Step 2. CHECK THE GROUND CIRCUIT OF THE HARNESS
The sensor remains disconnected from the machine harness.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the J1 and J2 machine harness connectors from the Machine ECM.
At the machine harness connector for the sensor, measure the resistance between ground contact 2 (wire 235-BK(Black)) and frame ground. Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The harness resistance is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5.0 ohms.Repair: The ground circuit in the harness has failed. There is an open circuit between the ground contact and frame ground. Repair or replace the machine harness.STOPTest Step 3. CHECK FOR A SHORTED HARNESS
The sensor and the Machine ECM remain disconnected from the machine harness.
The disconnect switch and the key start switch remain in the OFF position.
Measure the resistance between the signal contact C (wire T967-YL(Yellow)) and contact A (wire J850-WH(White)) of the machine harness connector for the sensor.Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to Test Step 4.
NOT OK - The resistance is less than 5000 ohms.Repair: The machine harness has failed. There is a short between the +battery circuit and the signal circuit in the machine harness. Repair or replace the machine harness.STOPTest Step 4. CHECK FOR AN OPEN HARNESS
The sensor and the Machine ECM remain disconnected from the machine harness.
The disconnect switch and the key start switch remain in the OFF position.
Measure the resistance of the signal circuit from the connector contact J1-54 (wire T967-YL(Yellow))

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
953D TRACK-TYPE LOADER LBP00001-UP (MACHINE) POWERED BY C6.6 Engine
963D TRACK-TYPE LOADER LCS00001-UP (MACHINE) POWERED BY C6.6 Engine


Parts control Caterpillar catalog:

2399954 CONTROL GP-UNPROGRAMMED
120M, 12M, 140M, 14M, 160M, 16M, 2384C, 2484C, 312C, 312D, 315C, 318C, 319C, 319D, 320C, 320C FM, 320D, 320D L, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 324D L, 3...
3074671 CONTROL GP-HANDLE
950H, 950K, 953D, 962H, 962K, 963D, 966H, 966K, 972H, 972K, 973D, 980H, 980K, 980K HLG, 986H, 988H, 992K, 993K, 994H, IT62H
2395025 CONTROL GP-UNPRGMED MONITOR
140G, 3126B, 3412E, 3606, 3608, 3612, 3616, 621B, 627F, 631D, 637D, 657E, 725, 730, 735, 740, 770, 772, 815B, 824C, 844K, 854K, 938H, 950H, 953D, 962H, 963D, 966H, 972H, 973D, 980C, 980G, 980H, 990K, ...
3722905 CONTROL GP-ELECTRONIC
120K, 12K, 12M, 140G, 140K, 140M, 140M 2, 14M, 160K, 160M, 160M 2, 16M, 2290, 2390, 2391, 2491, 24M, 2590, 345D L, 511, 521, 521B, 522, 522B, 525C, 532, 535C, 541, 541 2, 545C, 551, 552, 552 2, 583T, ...
2863686 CONTROL GP-ENGINE ELECTRONIC
953D, 963D, D6K, D6K LGP, D6N, PL61
3003631 CONTROL GP-UNPROGRAMMED
953D, 963D, D3K XL, D4K XL, D5K LGP, D6K, D6K LGP
3292576 CONTROL GP-UNPROGRAMMED
953D, 963D, 973D, D6K, D6K LGP, D6N, PL61
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.