2974588 CONTROL GP-HANDLE Caterpillar parts
318C, 320C, 321C, 322C, 325C, 330C, 330C L, 385B
Rating:
Alternative (cross code) number:
CA2974588
297-4588
2974588
CA2974588
297-4588
2974588
Weight: 0.75 pounds 0 kg.
EXCAVATOR, MOBILE HYD POWER UNIT,
This part in 5 request:
Show.
This information for suppliers only!
2024-05-02
2021-11-01
2020-08-21
2020-07-27
2018-10-16
Compatible equipment models: 2974588:
Number on catalog scheme:
1
For full view, you need register
Information:
Test Step 1. CHECK FOR POWER AT THE SENSOR
Turn the key start switch and the disconnect switch to the OFF position.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert 7X-1710 Multimeter Probes along voltage supply A (wire R800-OR(Orange)) and along return contact B (wire P967-PU(Purple)).
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact A to contact B. Expected Result:The voltage measurement is 8.0 0.5 DCV.Results:
OK - The voltage measurement is 8.0 0.5 DCV. The power supply circuit is correct. Proceed to Test Step 2.
NOT OK - The voltage measurement is not 8.0 0.5 DCV. The power supply circuit is not correct.Repair: There is a problem with the power supply circuit for the sensor. Refer to the complete Electrical System Schematic of the machine. Check all of the connections that are in the power supply circuit and the return circuit. Ensure that all connections are clean, that all connections are secure and that all connections are in good condition. Repair the machine harness or replace the machine harness. STOPTest Step 2. CHECK THE SENSORTurn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the "right steering cylinder" position sensor and disconnect the machine harness connector from the "left steering cylinder" position sensor. Mark the harness connector for the "right steering sensor".
Connect the marked connector for the "right steering sensor" to the connector for the "left steering sensor". Connect the connector that is not marked for the "left steering sensor" to the connector for the "right steering sensor" .
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the active diagnostic code for the right steering sensor. Expected Result:When the harness connectors are switched, the CID 2201 FMI 03 diagnostic code for the "right steering sensor" is not active. A CID 2200 FMI 03 diagnostic code for the "left steering sensor" is now active.Results:
YES - The CID 2201 FMI 03
Turn the key start switch and the disconnect switch to the OFF position.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert 7X-1710 Multimeter Probes along voltage supply A (wire R800-OR(Orange)) and along return contact B (wire P967-PU(Purple)).
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact A to contact B. Expected Result:The voltage measurement is 8.0 0.5 DCV.Results:
OK - The voltage measurement is 8.0 0.5 DCV. The power supply circuit is correct. Proceed to Test Step 2.
NOT OK - The voltage measurement is not 8.0 0.5 DCV. The power supply circuit is not correct.Repair: There is a problem with the power supply circuit for the sensor. Refer to the complete Electrical System Schematic of the machine. Check all of the connections that are in the power supply circuit and the return circuit. Ensure that all connections are clean, that all connections are secure and that all connections are in good condition. Repair the machine harness or replace the machine harness. STOPTest Step 2. CHECK THE SENSORTurn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the "right steering cylinder" position sensor and disconnect the machine harness connector from the "left steering cylinder" position sensor. Mark the harness connector for the "right steering sensor".
Connect the marked connector for the "right steering sensor" to the connector for the "left steering sensor". Connect the connector that is not marked for the "left steering sensor" to the connector for the "right steering sensor" .
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the active diagnostic code for the right steering sensor. Expected Result:When the harness connectors are switched, the CID 2201 FMI 03 diagnostic code for the "right steering sensor" is not active. A CID 2200 FMI 03 diagnostic code for the "left steering sensor" is now active.Results:
YES - The CID 2201 FMI 03
Caterpillar parts catalog:
Parts control Caterpillar catalog:
312C, 312C L, 315C, 318C, 319C, 320C, 320C FM, 320C L, 321C, 322C, 325C, 330C, 330C FM, 330C L, 330C MH, M325C MH
1958906
CONTROL GP-IMPLEMENT
318C, 319C
318C, 319C
318C, 320C, 321C, 322C, 325C, 330C, 330C L, 385B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 5090B
2475160
CONTROL GP-ELECTRONIC
385B, 5090B
385B, 5090B
2115564
CONTROL GP-MACHINE
322C, 322C FM
322C, 322C FM
2115537
CONTROL AS-ELECTRONIC
320C, 325C
320C, 325C
2475243
CONTROL GP
320C
320C
2115574
CONTROL GP
325C
325C
1958906
CONTROL GP-IMPLEMENT
318C, 319C
318C, 319C
0969506
CONTROL
318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
2597282
CONTROL GP-WASHER & WIPER
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
2014540
CONTROL GP-ELECTRONIC
314C, 321C
314C, 321C
3280651
CONTROL GP-WIPER
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320C, 320D FM, 320D FM RR, 322C, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 329D L, 330C, 330C L, 330D, 330D ...
312C, 312D, 315C, 315D L, 318C, 319C, 319D, 320C, 320D FM, 320D FM RR, 322C, 323D L, 323D LN, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325C, 325D, 325D FM, 325D L, 329D L, 330C, 330C L, 330D, 330D ...
311D LRR, 312C, 312D, 312D L, 314D CR, 314D LCR, 315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN, D6N, D6R III, D6T, D6T LGP
318C, 320C, 321C, 322C, 325C, 330C, 330C L, 385B