AVSPARE.COM
parts catalog

CONTROL AR-AUXILIARY 3237562 - Caterpillar



3237562 CONTROL AR-AUXILIARY Caterpillar parts 312D L CONTROL
Rating:
8
Alternative (cross code) number:
CA3237562
323-7562
3237562
Caterpillar 3237562 CONTROL AR-AUXILIARY

Buy CONTROL AR-AUXILIARY 3237562 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3237562:

EXCAVATOR  312D L   Caterpillar
  For full view, you need register

Information:


Illustration 1 g01775062
Connections of the forward low solenoidThis diagnostic code is associated with the forward low solenoid. The FMI 06 code means that the ECM has determined that the current of the solenoid is above normal.The possible causes of this diagnostic code are listed below:
The solenoid energizer circuit of the modulating valve is shorted to ground.
The solenoid has failed.
The ECM has failed. This situation is unlikely. Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and that all connections are secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1402 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the starter keyswitch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the transmission harness. Expected Result:The CID 1402 FMI 06 diagnostic code changes to a CID 1402 FMI 05 diagnostic code when the solenoid is disconnected.Results:
YES - The CID 1402 FMI 06 diagnostic code changes to a CID 1402 FMI 05 diagnostic code when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - The CID 1402 FMI 06 diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID ENERGIZER CIRCUIT FOR A SHORT TO GROUND
Turn the starter keyswitch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the transmission harness.
Disconnect the connectors of the transmission harness from the ECM.
At the connector for the transmission harness, measure the resistance from the signal contact J1-17 (wire 754-BU) to all contacts that are used in the connectors of the transmission harness for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The transmission harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the transmission harness. The short is between J1-17 (wire 754-BU) and the circuit with the low resistance measurement.Repair: Repair the transmission harness or replace the transmission harness. STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the harness connectors. Clean the contacts of the harness connectors and check the wires for damage to the insulation that is caused

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts control Caterpillar catalog:

2358970 CONTROL GP-HANDLE
307D, 308D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 315D L, 318D L, 318D2 L, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 32...
2705667 CONTROL GP-JOYSTICK
311D LRR, 312D, 312D L, 314D LCR, 315D L, 319D, 320D LRR, 321D LCR, 323D L, 323D LN, 324D, 324D L, 324D LN, 325D, 325D L, 329D L, 330D, 330D L, 330D LN
2358969 CONTROL GP-HANDLE
307D, 308D, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 315D L, 318D L, 318D2 L, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 32...
2970540 CONTROL GP-JOYSTICK
311D LRR, 312D, 312D L, 315D L, 319D, 319D L, 320D, 320D L, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325D, 325D L, 328D LCR, 329D, 329D L, 329D LN, 330D, 330D L, 330D LN, 33...
3317539 CONTROL GP-UNPROGRAMMED
120M, 12M, 2470C, 311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321D LCR, 323D L, 323D...
2974595 CONTROL GP-HANDLE
311D LRR, 312D, 312D L, 314D CR, 314D LCR, 315D L, 319D, 319D L, 320D, 320D L, 320D LRR, 320D RR, 320D2 L, 321D LCR, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325D, 325D L, 328D LCR, 329D, 329D...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.