AVSPARE.COM
parts catalog

CONTROL AS-ELECTRONIC 3759686 - Caterpillar


3759686 CONTROL AS-ELECTRONIC Caterpillar parts EPIC
Rating:
37
Alternative (cross code) number:
CA3759686
375-9686
3759686
Caterpillar 3759686 CONTROL AS-ELECTRONIC
Weight: 5 pounds 2 kg.

Buy CONTROL AS-ELECTRONIC 3759686 Caterpillar genuine, new aftermarket tractor parts with delivery
SWITCHGEAR,

Compatible equipment models: 3759686:

SWITCHGEAR  EPIC   Caterpillar
Number on catalog scheme: 3
  For full view, you need register

Information:


Illustration 1 g00927423
Illustration 2 g01134979
There are two manual actuators on the machine.Manual actuator (1) is located in the operator station of the machine. Manual actuator (3) is located on the left side of the radiator guard.Activate the fire suppression system by turning handle (2) or (4) counterclockwise.Fire Suppression Control (Engine Shutdown)
Illustration 3 g03715105
Engine shutdown control for fire suppression
Illustration 4 g03715106
Engine shutdown control for fire suppression and idle timerThe function of the fire suppression control is to cause a delayed engine shutdown when the fire suppression system is activated.
Fire System Activated (1) - This indicator indicates that the fire suppression system has been activated. When this indicator flashes, an alarm will sound and the engine will shut down after a six second delay.
Engine Shutdown Switch (2) - This switch allows the engine to be shut down immediately. Push and hold engine shutdown switch (2) down to shut down the engine. Note: During normal operation use the engine start switch to shut down the engine.
System Reset Button (3) - This button is used to override the fire suppression control so that the machine can be moved after discharge of the fire suppression system and loss of system pressure. The "SYSTEM RESET" button must be held in for the engine to operate. Upon release, the engine will shut down after 6 seconds.Note: The override function should only be used in an extreme emergency. Restarting the machine before the fire suppression system has been recharged can reignite the fire that had been previously suppressed, without a means of extinguishment.Idle Timer Function
Certain machines may be equipped with an idle timer control (engine shutdown) in addition to the fire suppression control.
Idle Timer On Indicator (4) - Indicates that the idle timer has been activated. When the engine start switch is turned to the OFF position, the indicator will flash and the engine will stop after 3 minutes. Note: The idle timer will activate whenever the engine start switch is turned from the ON position to the OFF position.To override the idle timer and stop the engine, turn the engine start switch to the OFF position and push the engine shutdown switch down.Note: If the idle timer has been activated without starting the engine, the idle timer can be deactivated by pushing down engine shutdown switch (2). Indicator (1) should stop flashing.
Never turn the battery disconnect switch to the OFF position with the idle timer activated (engine running). Electrical system damage could result.
In Case of Fire
In case of fire, evacuate the area to reduce the risk of injury from flames, heat, hazardous vapors, explosions, or any other hazards that may be created.
The following procedure should be read and performed in accordance with the current mine site practices.In case of fire perform the following procedure:
When a fire is detected or when the system alarm (if equipped) sounds, bring the machine to a safe controlled stop.
Stop the engine.
Engage the parking brake.
If not automatically activated, manually activate the fire suppression system by turning the handle on the manual fire suppression control counterclockwise.
Evacuate

Caterpillar parts catalog:

Caterpillar parts catalog
EPIC Engine Paralleling and Integration Control EPC00001-UP


Parts control Caterpillar catalog:

3724242 CONTROL GP-UNPROGRAMMED
CG137-08, CG137-12, G3516H
3408157 CONTROL GP-ELECTRONIC
120M 2, 2570C, 2670C, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 563C, 573C, 950K, 962K, C7.1
2622878 CONTROL GP-UNPROGRAMMED
120K, 120K 2, 12K, 140K, 140K 2, 160K, 725, 730, 962H, 966H, 972H, 980H, C15, C9, CX31-C9I, D6R III, TH31-E61, TH35-C13I, TH35-C15I
3722910 CONTROL GP-UNPROGRAMMED
12M 2, 12M 3, 140M 2, 160M 2, 3516C, 390F L, 627H, 627K, 725C, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K, C175-16, C9, D6T LGP, D6T XL, D7E, D7E LGP, D9T, TH31-E61
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.