AVSPARE.COM
parts catalog

CONTROL GP-GOVERNOR 3966915 - Caterpillar



3966915 CONTROL GP-GOVERNOR Caterpillar parts C1.5 CONTROL
Rating:
7
Alternative (cross code) number:
CA3966915
396-6915
3966915
Caterpillar 3966915 CONTROL GP-GOVERNOR

Buy CONTROL GP-GOVERNOR 3966915 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compatible equipment models: 3966915:

INDUSTRIAL ENGINE  C1.5   Caterpillar
Number on catalog scheme:
  
  For full view, you need register

Information:


Illustration 1 g01375179
Schematic of the left front drive motor solenoidThis diagnostic code is associated with the left front drive motor solenoid (all wheel drive). The FMI 13 diagnostic code is activated when the Implement ECM detects the left front drive motor solenoid that needs calibration. Once the calibration for the left front drive motor solenoid has been performed successfully, this diagnostic code will disappear. This failure is active on a new ECM.Possible causes of this diagnostic code are listed below:
The ECM has been replaced or new software has been installed.
The ECM has failed.System Response:The machine response is listed below:
AWD will not operate.Note: Ensure that you have repaired any condition that would cause other active diagnostic codes that are related to this solenoid. If the other diagnostic codes are active, troubleshoot those codes first. Then perform this procedure.Note: Ensure that the diagnostic code of CID 2293 FMI13 is active before performing this procedure.Test Step 1. CHECK THE CALIBRATION
Perform the calibration procedure. Refer to the Testing and Adjusting Section of the Service Manual for the correct procedure.
Observe the status of the CID 2293 FMI 13.Expected Result:The CID 2293 FMI 13 is active.Results:
OK - The CID 2293 FMI 13 is active. The diagnostic code has not been corrected. Verify that the correct software has been flashed into the ECM, or that the correct ECM is installed on the machine. Then repeat the calibration.Repair: If the diagnostic code is still active and the cause of the diagnostic code is not found replace the ECM. It is unlikely that the ECM has failed. Verify that the solenoid and associated circuits are correct before you replace the ECM.STOP
NOT OK - The CID 2293 FMI 13 is not active. The calibration corrected the condition that caused the diagnostic code. Repair: Resume normal operation.STOP

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C1.5 Industrial Engine G7P00001-UP


Parts control Caterpillar catalog:

2661427 CONTROL GP-GENERATOR SET
3406C, 3412C, 3456, C1.5, C15, C18, C2.2, C3.3, C4.4, C9
2615132 CONTROL GP-GENERATOR SET
3406C, 3412C, 3456, C1.5, C15, C18, C2.2, C3.3, C4.4, C9
3007645 CONTROL GP-GENERATOR SET
3406C, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C1.5, C15, C175-16, C18, C2.2, C27, C3.3, C32, C4.4, C6.6, C9, G3508, G3512
3007646 CONTROL GP-GENERATOR SET
3406C, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C1.5, C15, C175-16, C18, C2.2, C27, C3.3, C32, C4.4, C6.6, C9, G3508, G3512
3642717 CONTROL GP-GOVERNOR
C1.5, CB22B, CB24B, CB32B, CC24B
2762665 CONTROL AS-ELECTRONIC
3406C, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C1.5, C15, C175-16, C18, C2.2, C27, C3.3, C32, C4.4, C9, G3508, G3512
2762658 CONTROL AS-ELECTRONIC
3406C, 3412C, 3456, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C1.5, C15, C175-16, C18, C2.2, C27, C3.3, C32, C4.4, C6.6, C9, G3508, G3512
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.