4222302 CONTROL GP-ELECTRONIC Caterpillar parts
C-9, C13, C15, C7, C9
Rating:
Alternative (cross code) number:
CA4222302
422-2302
4222302
CA4222302
422-2302
4222302
Weight: 9 pounds 4 kg.
TRUCK ENGINE,
Related part:
4222302
CONT GP -E
10R6199
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
372-2912 289-1532 350-3648 422-2302 488-4879 C7 C9 C15 Engine ECU Controller Computer Panel. Compatible With Caterpillar With Program
ZHANGUSY ECM Precise Control: The vehicle engine computer module ECU can precisely control the engine, reducing fuel consumption while increasing power output || Intelligent Diagnosis: The engine electronic control module has an advanced fault diagnosis system. The electronic control unit can monitor the engine status in real time and quickly and accurately identify fault codes || Quality: The engine control module components are made of carefully selected materials and with exquisite craftsmanship, featuring excellent anti-interference and durability performance || Performance: The engine control computer processes data quickly to improve the overall operational efficiency of the vehicle and can be programmed by itself || Note: Please confirm your shipping address, the model and specification of the car computer board, the vehicle model and year, and compatibility || Attention: If the car with an installed ECU cannot start, please check if the car has an anti-theft function or if the key has a chip. If the car has an anti-theft function, successful decoding and matching (using a decoder) are required || Check Voltage: Check if the circuit is normal and if the grounding is good. Do not install it with a voltage higher than normal, otherwise it may burn out the computer board
ZHANGUSY ECM Precise Control: The vehicle engine computer module ECU can precisely control the engine, reducing fuel consumption while increasing power output || Intelligent Diagnosis: The engine electronic control module has an advanced fault diagnosis system. The electronic control unit can monitor the engine status in real time and quickly and accurately identify fault codes || Quality: The engine control module components are made of carefully selected materials and with exquisite craftsmanship, featuring excellent anti-interference and durability performance || Performance: The engine control computer processes data quickly to improve the overall operational efficiency of the vehicle and can be programmed by itself || Note: Please confirm your shipping address, the model and specification of the car computer board, the vehicle model and year, and compatibility || Attention: If the car with an installed ECU cannot start, please check if the car has an anti-theft function or if the key has a chip. If the car has an anti-theft function, successful decoding and matching (using a decoder) are required || Check Voltage: Check if the circuit is normal and if the grounding is good. Do not install it with a voltage higher than normal, otherwise it may burn out the computer board
372-2912 289-1532 350-3648 422-2302 488-4879 C7 C9 C15 Engine ECU Controller Computer Panel For Caterpillar with Program
ZHANGUSY ECM Precise Control: The vehicle engine computer module ECU can precisely control the engine, reducing fuel consumption while increasing power output || Intelligent Diagnosis: The engine electronic control module has an advanced fault diagnosis system. The electronic control unit can monitor the engine status in real time and quickly and accurately identify fault codes || Quality: The engine control module components are made of carefully selected materials and with exquisite craftsmanship, featuring excellent anti-interference and durability performance || Performance: The engine control computer processes data quickly to improve the overall operational efficiency of the vehicle and can be programmed by itself || Note: Please confirm your shipping address, the model and specification of the car computer board, the vehicle model and year, and compatibility || Attention: If the car with an installed ECU cannot start, please check if the car has an anti-theft function or if the key has a chip. If the car has an anti-theft function, successful decoding and matching (using a decoder) are required || Check Voltage: Check if the circuit is normal and if the grounding is good. Do not install it with a voltage higher than normal, otherwise it may burn out the computer board
ZHANGUSY ECM Precise Control: The vehicle engine computer module ECU can precisely control the engine, reducing fuel consumption while increasing power output || Intelligent Diagnosis: The engine electronic control module has an advanced fault diagnosis system. The electronic control unit can monitor the engine status in real time and quickly and accurately identify fault codes || Quality: The engine control module components are made of carefully selected materials and with exquisite craftsmanship, featuring excellent anti-interference and durability performance || Performance: The engine control computer processes data quickly to improve the overall operational efficiency of the vehicle and can be programmed by itself || Note: Please confirm your shipping address, the model and specification of the car computer board, the vehicle model and year, and compatibility || Attention: If the car with an installed ECU cannot start, please check if the car has an anti-theft function or if the key has a chip. If the car has an anti-theft function, successful decoding and matching (using a decoder) are required || Check Voltage: Check if the circuit is normal and if the grounding is good. Do not install it with a voltage higher than normal, otherwise it may burn out the computer board
Engine Control Module 4222302 - Replaces 422-2302 Controller | Fits for Cat C-9 C13 C15 C7 C9 Truck Engines | ECU ECM CPU Controller
LIUCHUANG Vehicle-Specific Fit: Engineered for Caterpillar C7, C9, and C13 truck engines; guarantees system compatibility || Direct Replacement: Matches reference number 422-2302, 4222302; simplifies installation with no modifications needed || Robust Build: Crafted to factory specifications; ensures long-lasting performance in rugged environments || Customizable Operation: Allows tailored programming; enhances engine efficiency for truck applications || Model Confirmation: Provide ECM number, VIN, and engine nameplate image post-purchase; verifies compatibility
LIUCHUANG Vehicle-Specific Fit: Engineered for Caterpillar C7, C9, and C13 truck engines; guarantees system compatibility || Direct Replacement: Matches reference number 422-2302, 4222302; simplifies installation with no modifications needed || Robust Build: Crafted to factory specifications; ensures long-lasting performance in rugged environments || Customizable Operation: Allows tailored programming; enhances engine efficiency for truck applications || Model Confirmation: Provide ECM number, VIN, and engine nameplate image post-purchase; verifies compatibility
Number on catalog scheme:
1
For full view, you need register
Information:
Remove & Install Cylinder Head Assembly
Start By:a. remove rocker shaft assemblies and push rodsb. remove water temperature regulatorc. remove fuel injection linesd. remove exhaust manifold1. Remove the intake manifold from the cylinder head. 2. Remove bolts (1) from the alternator bracket.3. Remove the bolts that hold plate (3), and remove the plate.4. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 5. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.6. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
7. Remove the gasket, seals (6) and O-ring seals (7) from the spacer plate. The following steps are for installation of the cylinder head. Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate.8. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (6) and two O-ring seals (7).9. Fasten a hoist, and put the cylinder head assembly in position on the cylinder block. 10. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts (5) to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).11. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 m (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).12. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And
Start By:a. remove rocker shaft assemblies and push rodsb. remove water temperature regulatorc. remove fuel injection linesd. remove exhaust manifold1. Remove the intake manifold from the cylinder head. 2. Remove bolts (1) from the alternator bracket.3. Remove the bolts that hold plate (3), and remove the plate.4. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 5. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.6. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
7. Remove the gasket, seals (6) and O-ring seals (7) from the spacer plate. The following steps are for installation of the cylinder head. Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate.8. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (6) and two O-ring seals (7).9. Fasten a hoist, and put the cylinder head assembly in position on the cylinder block. 10. Put clean engine oil on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts (5) to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).11. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 m (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).12. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And
Caterpillar parts catalog:
Parts control Caterpillar catalog:
2996270
CONTROL GP-CLEAN GAS INDUCTION
C15, TH35-C15T
C15, TH35-C15T
2996271
CONTROL GP-CLEAN GAS INDUCTION
C15, TH35-C15T
C15, TH35-C15T
3304496
CONTROL GP-CLEAN GAS INDUCTION
C15, TH35-C15T
C15, TH35-C15T
3304497
CONTROL GP-CLEAN GAS INDUCTION
C15, TH35-C15T
C15, TH35-C15T
3722910
CONTROL GP-UNPROGRAMMED
12M 2, 12M 3, 140M 2, 160M 2, 3516C, 390F L, 627H, 627K, 725C, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K, C175-16, C9, D6T LGP, D6T XL, D7E, D7E LGP, D9T, TH31-E61
12M 2, 12M 3, 140M 2, 160M 2, 3516C, 390F L, 627H, 627K, 725C, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 988K, C175-16, C9, D6T LGP, D6T XL, D7E, D7E LGP, D9T, TH31-E61
3024, 3116, 3126, 3126B, 3126E, 3176B, 3406E, C-10, C-12, C-15, C-16, C-9, C11, C13, C15, C7, C9, CX28, CX31, CX35, DEUCE, TH31-E61, TH35-C13T, TH35-C15T
C-9, C13, C15, C7, C9, TH31-E61
2864452
CONTROL GP-ENGINE ELECTRONIC
C13, C15, C7, C9, TH35-C13T, TH35-C15T
C13, C15, C7, C9, TH35-C13T, TH35-C15T
2864449
CONTROL GP-MACHINE
C9, TH31-E61
C9, TH31-E61
2808906
CONTROL GP-ELECTRONIC
C13, C15, TH35-C15T
C13, C15, TH35-C15T
2864451
CONTROL GP-ELECTRONIC
C13, C15, TH35-C15T
C13, C15, TH35-C15T
C13, C15, TH35-C13T, TH35-C15T
2864452
CONTROL GP-ENGINE ELECTRONIC
C13, C15, C7, C9, TH35-C13T, TH35-C15T
C13, C15, C7, C9, TH35-C13T, TH35-C15T
C-9, C13, C15, C7, C9, TH31-E61
C15, C18
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 651B, 657E, 657G, 770, 772, 950H, 962H, AP-755, C7, C9, IT62H, PM-200, PM-201, W345C MH
2267475
CONTROL GP-ENGINE ELECTRONIC
365C, 365C L, 365C L MH, 385C, 385C FS, 385C L, 385C L MH, 586C, 627G, 637D, 637E, 637G, C7, C9, TH31-E61
365C, 365C L, 365C L MH, 385C, 385C FS, 385C L, 385C L MH, 586C, 627G, 637D, 637E, 637G, C7, C9, TH31-E61
324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D...
C13, C15
1962087
CONTROL GP-MONITOR
3508B, 3512, 3512B, 3512C, 3516B, TH48-E80
3508B, 3512, 3512B, 3512C, 3516B, TH48-E80
C13, C15, TH35-C13T, TH35-C15T
2864451
CONTROL GP-ELECTRONIC
C13, C15, TH35-C15T
C13, C15, TH35-C15T
2808906
CONTROL GP-ELECTRONIC
C13, C15, TH35-C15T
C13, C15, TH35-C15T
2864449
CONTROL GP-MACHINE
C9, TH31-E61
C9, TH31-E61