6I2948 CONTROL GP-ENGINE ELECTRONIC Caterpillar parts
3406B
Rating:
Alternative (cross code) number:
CA6I2948
6I-2948
6I2948
CA6I2948
6I-2948
6I2948
Weight: 9 pounds 4 kg.
TRUCK ENGINE,
Compatible equipment models: 6I2948:
Number on catalog scheme:
For full view, you need register
Information:
TYPE="LEVEL" DEPTH="1" @@@-->Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
B 207-1600(1) Rubber Lubricant -
207-1601 Rubber Lubricant -
C - LOCTITE 263 -
- LOCTITE 270(2) -
(1) For use in EAME
(2) Europe OnlyStart By:
Remove the fuel temperature sensor.
Remove the fuel pressure sensor.
Personal injury or death can result from a fire.Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.Clean up all leaked or spilled fuel. Do not smoke while working on the fuel system.Turn the disconnect switch OFF or disconnect the battery when changing fuel filters.
Turn the fuel supply to the OFF position.
Illustration 1 g03056698
Relive fuel pressure by opening relief valve (2).
Disconnect hose assemblies (1) and the adapters. Disconnect hose (2).
Use Tooling (A) to remove fuel filters (5).
Remove fuel filter base (4).
Illustration 2 g03057097
Remove fuel priming pump (6) and discard the gasket. Use a new gasket for installation.
Remove plugs (7) and pipe plugs (7).
Remove valve assembly (9) and the adapter.
Illustration 3 g03057139
Remove plug assembly (10) and remove studs (11).
Illustration 4 g03057179
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Note: Illustration 4 shows lever (18) in the FLOW BOTH position.Note: Note the indicator on lever (18) is aligned with the flat grooves on fuel filter valve (13).
Remove spring pin (19).
Remove lever (18), ball (15), and spring (12).
Remove screws (17) and plate (12).
Remove fuel filter valve (13) and discard O-ring seals (16).Installation Procedure
Install fuel filter base (4) in the reverse order of removal.
Lubricate O-ring seals (16) and the bores with Tooling (B).
Illustration 5 g03057396
Note the indicator on lever (18) is aligned with the flat grooves on fuel filter valve (13). Reference Illustration 5.
Apply Tooling (C) 7.6 mm (0.30 inch) from the tapered end of studs (11).
Apply Tooling (B) to plugs (7).
Turn fuel filters (5) one full turn after the filter gaskets come in contact with the base.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
B 207-1600(1) Rubber Lubricant -
207-1601 Rubber Lubricant -
C - LOCTITE 263 -
- LOCTITE 270(2) -
(1) For use in EAME
(2) Europe OnlyStart By:
Remove the fuel temperature sensor.
Remove the fuel pressure sensor.
Personal injury or death can result from a fire.Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.Clean up all leaked or spilled fuel. Do not smoke while working on the fuel system.Turn the disconnect switch OFF or disconnect the battery when changing fuel filters.
Turn the fuel supply to the OFF position.
Illustration 1 g03056698
Relive fuel pressure by opening relief valve (2).
Disconnect hose assemblies (1) and the adapters. Disconnect hose (2).
Use Tooling (A) to remove fuel filters (5).
Remove fuel filter base (4).
Illustration 2 g03057097
Remove fuel priming pump (6) and discard the gasket. Use a new gasket for installation.
Remove plugs (7) and pipe plugs (7).
Remove valve assembly (9) and the adapter.
Illustration 3 g03057139
Remove plug assembly (10) and remove studs (11).
Illustration 4 g03057179
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Note: Illustration 4 shows lever (18) in the FLOW BOTH position.Note: Note the indicator on lever (18) is aligned with the flat grooves on fuel filter valve (13).
Remove spring pin (19).
Remove lever (18), ball (15), and spring (12).
Remove screws (17) and plate (12).
Remove fuel filter valve (13) and discard O-ring seals (16).Installation Procedure
Install fuel filter base (4) in the reverse order of removal.
Lubricate O-ring seals (16) and the bores with Tooling (B).
Illustration 5 g03057396
Note the indicator on lever (18) is aligned with the flat grooves on fuel filter valve (13). Reference Illustration 5.
Apply Tooling (C) 7.6 mm (0.30 inch) from the tapered end of studs (11).
Apply Tooling (B) to plugs (7).
Turn fuel filters (5) one full turn after the filter gaskets come in contact with the base.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts control Caterpillar catalog:
6Y5501
CONTROL GP-STEERING & TMSN
D6H, D6H II, D6H XL, D6H XR
D6H, D6H II, D6H XL, D6H XR
130G, 1673C, 3306, 571G, 572G, 950, 955K, 955L, 966C, 980B, D4D, D4E, D5, D6C, D7F, D7G
2238220
CONTROL-THROTTLE
3126, 3126B, 3196, 3406E, 3412E, C-12, C12, C15, C18, C30, C32, C7, C9
3126, 3126B, 3196, 3406E, 3412E, C-12, C12, C15, C18, C30, C32, C7, C9
3E7706
CONTROL GP-ELECTRONIC
65C, 70C, 75C, 75D, 85C
65C, 70C, 75C, 75D, 85C
1138667
CONTROL GP-STEERING
45, 55
45, 55
5V6050
CONTROL GP-BRAKE
950B, 950B/950E
950B, 950B/950E
3712887
CONTROL & MTG GP-MACHINE
CB-44B, CB-54B, CD-54B
CB-44B, CB-54B, CD-54B
6R0699
CONTROL GP-CONV/AUGER PUMP DR
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, BG-225B
AP-1000, AP-1050, AP-1200, AP-800, AP-800C, BG-225B
2224906
CONTROL GP-IGNITION
G3520B
G3520B
3V4443
CONTROL GP-SWING BRAKE
245, 245B, 245D
245, 245B, 245D