9T5989 CONVERSION GP-FIELD Caterpillar parts
446
Rating:
Alternative (cross code) number:
CA9T5989
9T-5989
9T5989
CA9T5989
9T-5989
9T5989
BACKHOE LOADER,
Compatible equipment models: 9T5989:
Number on catalog scheme:
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the engine oil pump, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8167, "Reconditioning Procedures 3114 and 3116 Engines".
Ensure that all of the parts of the engine oil pump are thoroughly clean prior to assembly. Note: Lubricate all internal parts of the engine oil pump with clean engine oil.
Illustration 1 g00824021
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install oil pressure relief plunger (13) and spring (14) in oil pump body assembly (7). Install the washer and the bolt.
Illustration 2 g00614694
Illustration 3 g00614689
Install shaft assembly (12) in oil pump body (9).
Install shaft assembly (11) in oil pump body (9).
Position oil pump body (9) on oil pump body assembly (7) and install bolts (10).
Illustration 4 g00614683
Press drive gear (8) on shaft assembly (11) until drive gear (8) is flush with the end of shaft assembly (11).
Install oil pump shaft (6). Install the bearing in idler gear (5) with Tooling (A). Install the bearing so the distance between the hub bolt face of idler gear (5) and the bearing is 0.75 0.25 mm (0.030 0.010 inch).
Illustration 5 g00614677
Install idler gear (5) on oil pump shaft (6). Install washer (4) and bolt (3). Tighten bolt (3) to 70 15 N m (52 11 lb ft).
Illustration 6 g00614664
Check the condition of the gasket that is used in tube assembly for the pickup of oil (2). If the gasket is damaged, replace the gasket. Install the gasket and tube assembly for the pickup of oil (2).
Check the condition of the O-ring seal that is used in outlet elbow (1). If the O-ring seal is damaged, replace the O-ring seal. Install the O-ring seal and outlet elbow (1). End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the engine oil pump, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8167, "Reconditioning Procedures 3114 and 3116 Engines".
Ensure that all of the parts of the engine oil pump are thoroughly clean prior to assembly. Note: Lubricate all internal parts of the engine oil pump with clean engine oil.
Illustration 1 g00824021
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install oil pressure relief plunger (13) and spring (14) in oil pump body assembly (7). Install the washer and the bolt.
Illustration 2 g00614694
Illustration 3 g00614689
Install shaft assembly (12) in oil pump body (9).
Install shaft assembly (11) in oil pump body (9).
Position oil pump body (9) on oil pump body assembly (7) and install bolts (10).
Illustration 4 g00614683
Press drive gear (8) on shaft assembly (11) until drive gear (8) is flush with the end of shaft assembly (11).
Install oil pump shaft (6). Install the bearing in idler gear (5) with Tooling (A). Install the bearing so the distance between the hub bolt face of idler gear (5) and the bearing is 0.75 0.25 mm (0.030 0.010 inch).
Illustration 5 g00614677
Install idler gear (5) on oil pump shaft (6). Install washer (4) and bolt (3). Tighten bolt (3) to 70 15 N m (52 11 lb ft).
Illustration 6 g00614664
Check the condition of the gasket that is used in tube assembly for the pickup of oil (2). If the gasket is damaged, replace the gasket. Install the gasket and tube assembly for the pickup of oil (2).
Check the condition of the O-ring seal that is used in outlet elbow (1). If the O-ring seal is damaged, replace the O-ring seal. Install the O-ring seal and outlet elbow (1). End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts conversion Caterpillar catalog:
6E0649
CONVERSION GP-FIELD
950B/950E, 966D, 966F, 966F II
950B/950E, 966D, 966F, 966F II
9R4342
CONVERSION GP-NON-ROPS
446, 446B
446, 446B