2388648 COOLANT-ELC Caterpillar parts
Rating:
Alternative (cross code) number:
CA2388648
238-8648
2388648
CA2388648
238-8648
2388648
Weight: 9 pounds 4 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CAT 238-8648 Extended Life Coolant 50/50 Premix, Red - 1 Gallon Jug (Case of 6)
CAT Factory-Fill—Used as standard factory-fill for all Cat machine cooling systems. || Lower Maintenance Costs—Reduces engine coolant and additive costs by as much as 500% compared to conventional coolants. It eliminates the need for supplemental coolant additives, extends coolant change-out intervals and reduces disposal requirements. || Advanced Metal Protection—Incorporates an advanced formula technology with organic acid additive corrosion inhibitors, such as a combination of mono and dicarboxylates for maximum protection of copper, solder, brass, steel, cast iron and aluminum. || Cat ELC is developed, tested and approved by Caterpillar to meet the same high standards as all Genuine Cat Parts. || Contains Bittering Agent || INGREDIENTS: Ethylene glycol, Sodium 2-ethylhexanoate, Tolyltriazole.
CAT Factory-Fill—Used as standard factory-fill for all Cat machine cooling systems. || Lower Maintenance Costs—Reduces engine coolant and additive costs by as much as 500% compared to conventional coolants. It eliminates the need for supplemental coolant additives, extends coolant change-out intervals and reduces disposal requirements. || Advanced Metal Protection—Incorporates an advanced formula technology with organic acid additive corrosion inhibitors, such as a combination of mono and dicarboxylates for maximum protection of copper, solder, brass, steel, cast iron and aluminum. || Cat ELC is developed, tested and approved by Caterpillar to meet the same high standards as all Genuine Cat Parts. || Contains Bittering Agent || INGREDIENTS: Ethylene glycol, Sodium 2-ethylhexanoate, Tolyltriazole.
CAT 238-8648 Extended Life Coolant 50/50 Premix - Red (1 Gallon)
CAT Drain Interval: 12,000 hours with SOS(SM) || Cat ELC is recommended in most Cat machine engine and machines. Do Not Add Water to dilute. || Lowers maintenance costs by eliminating the need for supplemental coolant additives, extends coolant change-out intervals, and reduces disposal requirements. || Cat ELC incorporates an advanced technology with organic acid corrosion inhibitors for maximum copper, solder, brass, steel, cast iron, and aluminum. protection.
CAT Drain Interval: 12,000 hours with SOS(SM) || Cat ELC is recommended in most Cat machine engine and machines. Do Not Add Water to dilute. || Lowers maintenance costs by eliminating the need for supplemental coolant additives, extends coolant change-out intervals, and reduces disposal requirements. || Cat ELC incorporates an advanced technology with organic acid corrosion inhibitors for maximum copper, solder, brass, steel, cast iron, and aluminum. protection.
$220.00
02 Jul 2022
US: D.S WHOLESALE
Caterpillar Marine 238-8648 ELC Extended Life Coolant (CASE OF 6)
Caterpillar Marine
Caterpillar Marine
This part in 6 request:
Show.
This information for suppliers only!
2023-02-06
2022-02-09
2020-09-10
2020-05-25
2020-02-11
2020-02-03
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 350-7768 Electric Hydraulic Pump Gp (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
6V-3175 Double Acting Cylinder 1
4C-9634 Puller Stud 1
9U-6832 Nut 1
4K-0684 Hard Washer 1
8M-4856 Sleeve 1
1P-1835 Bearing Puller Adapter 1 Start By:
Remove the ripper lift cylinder.
Remove the ripper carriage.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Illustration 1 g00860732
Install lift cylinder pin (3) . Attach a suitable lifting device to ripper frame (2) and lift cylinder pin (3) . Remove pins (1) and ripper frame (2) . The weight of ripper frame (2) is approximately 454 kg (1000 lb).
Illustration 2 g03342600
Note: Typical example.
Use Tooling (A) to remove bearings (4) . Remove bearings (4) from ripper frame (2) .Installation Procedure
Lower the temperature of bearings (4) . Use Tooling (A) to install bearings (4) .
Illustration 3 g00860732
Attach a suitable lifting device to ripper frame (2) and lift cylinder pin (3) . Install ripper frame (2) . The weight of ripper frame (2) is approximately 454 kg (1000 lb). Install pins (1) . Use shims to tighten the frame. Remove the lifting device and remove lift cylinder pin (3) .End By:
Install the ripper carriage.
Install the ripper lift cylinder.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 350-7768 Electric Hydraulic Pump Gp (115V) 1
350-7769 Electric Hydraulic Pump Gp (230V) 1
6V-3175 Double Acting Cylinder 1
4C-9634 Puller Stud 1
9U-6832 Nut 1
4K-0684 Hard Washer 1
8M-4856 Sleeve 1
1P-1835 Bearing Puller Adapter 1 Start By:
Remove the ripper lift cylinder.
Remove the ripper carriage.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death.
Illustration 1 g00860732
Install lift cylinder pin (3) . Attach a suitable lifting device to ripper frame (2) and lift cylinder pin (3) . Remove pins (1) and ripper frame (2) . The weight of ripper frame (2) is approximately 454 kg (1000 lb).
Illustration 2 g03342600
Note: Typical example.
Use Tooling (A) to remove bearings (4) . Remove bearings (4) from ripper frame (2) .Installation Procedure
Lower the temperature of bearings (4) . Use Tooling (A) to install bearings (4) .
Illustration 3 g00860732
Attach a suitable lifting device to ripper frame (2) and lift cylinder pin (3) . Install ripper frame (2) . The weight of ripper frame (2) is approximately 454 kg (1000 lb). Install pins (1) . Use shims to tighten the frame. Remove the lifting device and remove lift cylinder pin (3) .End By:
Install the ripper carriage.
Install the ripper lift cylinder.
Parts coolant Caterpillar catalog:
Caterpillar
2374953
COOLANT-ELC
Caterpillar
Caterpillar
2339799
COOLANT-NGEC
Caterpillar
Caterpillar
2339798
COOLANT-NGEC
Caterpillar
Caterpillar
2339797
COOLANT-NGEC
Caterpillar
Caterpillar
2221534
COOLANT-ELC
Caterpillar
Caterpillar
2993664
COOLANT GP-
Caterpillar
Caterpillar
2478281
COOLANT-NGEC
Caterpillar
Caterpillar
2393649
COOLANT-NGEC
Caterpillar
Caterpillar
2388653
COOLANT-DEAC
Caterpillar
Caterpillar
2388651
COOLANT-DEAC
Caterpillar
Caterpillar
Caterpillar