9Y1901 CORD AS Caterpillar parts
3406B, 3406C
Rating:
Alternative (cross code) number:
CA9Y1901
9Y-1901
9Y1901
CA9Y1901
9Y-1901
9Y1901
Weight: 0.75 pounds 0 kg.
GEN SET ENGINE, GENERATOR SET,
This part in 2 request:
Show.
This information for suppliers only!
2022-12-20
2020-08-07
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ 6V-9508 Face Seal Plug 1
6V-9511 Face Seal Plug 1
6V-9829 Cap As 1
6V-9832 Cap As 1 Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic oil from the hydraulic system into a suitable container for storage or disposal. The capacity of the hydraulic system is 76 L (20.1 US gal).
Illustration 1 g00984058
Disconnect hose assemblies (1) and (2) .
Remove bolts (4). Remove vane pump (3) .
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ 6V-9508 Face Seal Plug 1
6V-9511 Face Seal Plug 1
6V-9829 Cap As 1
6V-9832 Cap As 1 Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic oil from the hydraulic system into a suitable container for storage or disposal. The capacity of the hydraulic system is 76 L (20.1 US gal).
Illustration 1 g00984058
Disconnect hose assemblies (1) and (2) .
Remove bolts (4). Remove vane pump (3) .
Caterpillar parts catalog:
Parts cord Caterpillar catalog:
1426113
CORD AS
3406C, C18
3406C, C18
7C9107
CORD AS
3208
3208
7E5033
CORD AS
3208
3208
120M, 120M 2, 12M, 320D2, 320D2 L, 323D2 L, 336E LN, 924H, 924HZ, 924K, 928HZ, 930K, 938H, 938K, 950K, 953D, 962K, 963D, C6.6, C7.1, D6K LGP, D6K2 LGP, D6N, D6N LGP, D6N OEM, IT38H, PL61
2601569
CORD AS-HEATER
120M, 120M 2, 12M, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 336E HVG, 336E LH, 336E LN, 924H, 924HZ, 924K, 928HZ, 930K, 938H, 938K, 950 GC, 950K, 953D, 962K, 963D, C6.6, C7.1, D5R LGP, D6K LGP, D6K2...
120M, 120M 2, 12M, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L, 336E HVG, 336E LH, 336E LN, 924H, 924HZ, 924K, 928HZ, 930K, 938H, 938K, 950 GC, 950K, 953D, 962K, 963D, C6.6, C7.1, D5R LGP, D6K LGP, D6K2...
C-12, C12, C18, C32
2137328
CORD AS
3126B, C7
3126B, C7
2677294
CORD AS-HEATER ELEMENT
3406C, 3456, C15, C18, C9
3406C, 3456, C15, C18, C9
2103207
CORD AS
3456
3456
2473472
CORD AS
3456, C15, C18
3456, C15, C18
1665017
CORD AS
3406E
3406E
1426113
CORD AS
3406C, C18
3406C, C18
1426112
CORD AS
3306B
3306B