0968221 CORE RADIAT Caterpillar parts
Rating:
Alternative (cross code) number:
CA0968221
096-8221
0968221
CA0968221
096-8221
0968221
Information:
Illustration 1 g03326619
Schematic of the "Single Tilt" solenoid
The CID 1047 diagnostic code is associated with the "Single Tilt" solenoid. The FMI 05 diagnostic code is recorded when the Implement ECM reads the current of the solenoid as being below normal.The possible causes are listed below:
There is an open in the circuit.
The solenoid has failed.
The ECM has failed. This condition is unlikely.System Response:
A level 2 warning will be generated.
All functions of "Single Tilt and Pitch" are lost.Note: Ensure that the CID 1047 FMI 05 diagnostic code for the solenoid is active.Note: The following procedure can create numerous related diagnostic codes. When all harnesses are reconnected, the related diagnostic codes will be shown as being not active. Clear all related diagnostic codes after this procedure is completed.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the machine harness from the solenoid.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 554-PK(Pink)) to contact 2 (wire H868-WH(White)).
Observe the status of the diagnostic code. Expected Result:The CID 1047 FMI 05 diagnostic code is no longer active. A CID 1047 FMI 06 diagnostic code is active after the jumper wire is connected.Results:
OK - The CID 1047 FMI 05 diagnostic code is no longer active. A CID 1047 FMI 06 diagnostic code is active after the jumper wire is connected. The solenoid has failed.Repair: Replace the solenoid. Verify that the new solenoid corrects the problem.STOP
NOT OK - The CID 1047 FMI 05 diagnostic code remains active. The jumper wire does not affect the status of the diagnostic code. The solenoid is not causing the problem. Proceed to test step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J2 machine harness connector from the ECM.
At the machine harness connector for the solenoid, the jumper wire remains installed.
At J2 machine harness connector, measure the resistance from contact J2-5 (wire 554-PK(Pink)) to J2-8 (wire H868-WH(White)). Expected Result:The resistance should be less than 5.0 ohms.Results:
YES - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to test step 3.
NO - The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in the wire for the solenoid signal or in wire (H868-WH(White)) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE STATUS OF THE DIAGNOSTIC CODE
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Check if the CID 1047 FMI 05 diagnostic code is active. Expected Result:The CID 1047 FMI 05 diagnostic code is not active.Results:
OK - The CID 1047 FMI 05 diagnostic code is no longer active. The diagnostic code
Parts core Caterpillar catalog:
0958563
CORE
Caterpillar
Caterpillar
0954577
CORE
Caterpillar
Caterpillar
0954573
CORE,RADIATR
Caterpillar
Caterpillar
0948483
CORE
Caterpillar
Caterpillar
0948206
CORE A,RADIA
Caterpillar
Caterpillar
0948163
CORE A,RADIA
Caterpillar
Caterpillar
0R3370
CORE GP-OIL
Caterpillar
Caterpillar
0R3368
CORE GP-OIL
Caterpillar
Caterpillar
0R3346
CORE GP-OIL
Caterpillar
Caterpillar
0R3332
CORE GP-O CLR
Caterpillar
Caterpillar
0983691
CORE ASSY
Caterpillar
Caterpillar
0980969
CORE ASSEMBLY
Caterpillar
Caterpillar