0R4753 CORE AS-OCLR Caterpillar parts
   
 
 
Rating:
 Alternative (cross code) number:
CA0R4753
0R-4753
0R4753
 
CA0R4753
0R-4753
0R4753
 
  Weight: 27 pounds 12 kg. 
  Related part:
 
1052077 
CORE AS-OCLR 
 0R4753 
 R
 Information:
 Linkage Adjustment Procedure:
1. With control lever (5) and governor control shaft in stop position, put lever (8) and pedal (2) in the positions shown. Adjust rods (6) and (7) and install pins in rod ends.2. With pedal (2) at Low Idle position, adjust length of cable (3) so hand control knob (1) is fully depressed. Tighten nuts for rod ends to ... 32 5 lb. ft.(45 7 N m)Tighten nut (4) to ... 9 3 lb. ft.(12 4 N m)For 977L Track-Type Loader
Linkage Adjustment Procedure:
With control lever (2) in shutoff position at angle (B), lever (1) at angle (A) and governor control shaft in shutoff position, put lever (6) on shaft at angle (D).Angle (A) is ... 107°Angle (B) is ... 34°Angle (D) is ... 20°Dimension (C) is ... 24.49 in.(622.0 mm)Tighten nuts (3) to ... 9 3 lb. ft.(12 4 N m)Dimension (E) is ... 67.84 in.(1723.1 mm)Tighten nuts (4) and (5) to ... 9 3 lb. ft.(12 4 N m)For 966C Wheel Loader & 814 Tractor
Linkage Adjustment Procedure:
With lever (1) in stop position and lever (2) and pedal (3) in positions shown, adjust length of rods (4) and (5). Connect the rods to the pedal and levers.Angle B is ... 90°Dimension (A) is ... 8.25 .06 in.(209.6 1.5 mm)Tighten nuts on rods to ... 9 3 lb. ft.(12 4 N m)For 627 Tractor
Linkage Adjustment Procedure:
With control lever (1) in High Idle position, rod end (2) must be assembled when the rod for the rotochamber is extended to full stroke. The center of the hole in rod end (2) is to be .06 .06 in. (1.5 1.5 mm) beyond the center of the threaded hole in control lever (1).Dimensions (A), (B) and (C) are measured from end of rod to back of nut.Dimension (A) and (B) ... .56 .06 in.(14.3 1.5 mm)Dimension (X) ... 22.0 .04 in.(558.8 1.0 mm)Dimension (C) ... .46 .06 in.(11.7 1.5 mm)Dimension (Y) ... 24.0 .04 in.(609.6 1.0 mm)Tighten nuts on rods to ... 9 3 lb. ft.(12 4 N m)For 627 Scraper
Linkage Adjustment Procedure:
With control lever (1) in shutoff position and governor control shaft (2) in shutoff position, put lever (1) on shaft.Dimension (A) ... 3.118 0.6 in.(79.2 1.5 mm)Tighten bolt (3) to ... 32 5 lb. ft.(45 7 N m)Tighten nut (4) to ... 9 3 lb. ft.(12 4 N m)Tighten nut (5) to ... 9 3 lb. ft.(12 4 N m)
 1. With control lever (5) and governor control shaft in stop position, put lever (8) and pedal (2) in the positions shown. Adjust rods (6) and (7) and install pins in rod ends.2. With pedal (2) at Low Idle position, adjust length of cable (3) so hand control knob (1) is fully depressed. Tighten nuts for rod ends to ... 32 5 lb. ft.(45 7 N m)Tighten nut (4) to ... 9 3 lb. ft.(12 4 N m)For 977L Track-Type Loader
Linkage Adjustment Procedure:
With control lever (2) in shutoff position at angle (B), lever (1) at angle (A) and governor control shaft in shutoff position, put lever (6) on shaft at angle (D).Angle (A) is ... 107°Angle (B) is ... 34°Angle (D) is ... 20°Dimension (C) is ... 24.49 in.(622.0 mm)Tighten nuts (3) to ... 9 3 lb. ft.(12 4 N m)Dimension (E) is ... 67.84 in.(1723.1 mm)Tighten nuts (4) and (5) to ... 9 3 lb. ft.(12 4 N m)For 966C Wheel Loader & 814 Tractor
Linkage Adjustment Procedure:
With lever (1) in stop position and lever (2) and pedal (3) in positions shown, adjust length of rods (4) and (5). Connect the rods to the pedal and levers.Angle B is ... 90°Dimension (A) is ... 8.25 .06 in.(209.6 1.5 mm)Tighten nuts on rods to ... 9 3 lb. ft.(12 4 N m)For 627 Tractor
Linkage Adjustment Procedure:
With control lever (1) in High Idle position, rod end (2) must be assembled when the rod for the rotochamber is extended to full stroke. The center of the hole in rod end (2) is to be .06 .06 in. (1.5 1.5 mm) beyond the center of the threaded hole in control lever (1).Dimensions (A), (B) and (C) are measured from end of rod to back of nut.Dimension (A) and (B) ... .56 .06 in.(14.3 1.5 mm)Dimension (X) ... 22.0 .04 in.(558.8 1.0 mm)Dimension (C) ... .46 .06 in.(11.7 1.5 mm)Dimension (Y) ... 24.0 .04 in.(609.6 1.0 mm)Tighten nuts on rods to ... 9 3 lb. ft.(12 4 N m)For 627 Scraper
Linkage Adjustment Procedure:
With control lever (1) in shutoff position and governor control shaft (2) in shutoff position, put lever (1) on shaft.Dimension (A) ... 3.118 0.6 in.(79.2 1.5 mm)Tighten bolt (3) to ... 32 5 lb. ft.(45 7 N m)Tighten nut (4) to ... 9 3 lb. ft.(12 4 N m)Tighten nut (5) to ... 9 3 lb. ft.(12 4 N m)
Parts core Caterpillar catalog:
 20R2661
CORE AS-OCLR
 
Caterpillar
 
Caterpillar
 10R8649
CORE AS-OCLR
 
Caterpillar
 
Caterpillar
 0R4187
CORE AS-OIL CLR
 
Caterpillar
 
Caterpillar
 5137996
CORE AS-OCLR-YM
 
Caterpillar
 
Caterpillar
 5230534
CORE-OCLR-YM
 
Caterpillar
 
Caterpillar
 5183980
CORE-AS-OCLR-YM
 
Caterpillar
  
Caterpillar
 0R8084
CORE AS-OIL CLR
 
Caterpillar
 
Caterpillar
 0R3362
CORE GP-OIL CLR
 
Caterpillar
 
Caterpillar
 0R3360
CORE GP-O CLR
 
Caterpillar
 
Caterpillar
 0R4755
CORE AS-OCLR
 
Caterpillar
 
Caterpillar
 0R8411
CORE AS-OCLR
 
Caterpillar
 
Caterpillar
 0R3708
CORE AS-OCLR
 
Caterpillar
 
Caterpillar