2013771 CORE AS-OIL COOLER Caterpillar parts
308C
Rating:
Alternative (cross code) number:
CA2013771
201-3771
2013771
CA2013771
201-3771
2013771
Weight: 5 pounds 2 kg.
Information:
CORE DEPTH
31
mm
CORE HEIGHT
440
mm
CORE WIDTH
443.6
mm
MINI HYD EXCAVATOR,
Compatible equipment models: 2013771:
Number on catalog scheme:
1
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 5P-9722 Seal Driver 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01156016
Use Tooling (A) and a suitable press in order to install shaft assembly (9) in water pump housing (8) . After installation, the bearing on shaft assembly (9) should be flush with the face of water pump housing (8) .
Use Tooling (B) to install seal (7) over shaft assembly (9) and into water pump housing (8) .
Use Tooling (A) and a suitable press in order to install impeller (6) onto shaft assembly (9) . Install impeller (6) until the distance between impeller (6) and the machined surface of water pump housing (8) is 0.75 0.25 mm (0.030 0.010 inch).
Position gasket (5) and rear cover (4) on water pump housing (8) . Install bolts (3) .Note: Check the O-ring seals for wear or for damage. If necessary, replace the O-ring seals.
Install O-ring seals (1) and (2) .End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 5P-9722 Seal Driver 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01156016
Use Tooling (A) and a suitable press in order to install shaft assembly (9) in water pump housing (8) . After installation, the bearing on shaft assembly (9) should be flush with the face of water pump housing (8) .
Use Tooling (B) to install seal (7) over shaft assembly (9) and into water pump housing (8) .
Use Tooling (A) and a suitable press in order to install impeller (6) onto shaft assembly (9) . Install impeller (6) until the distance between impeller (6) and the machined surface of water pump housing (8) is 0.75 0.25 mm (0.030 0.010 inch).
Position gasket (5) and rear cover (4) on water pump housing (8) . Install bolts (3) .Note: Check the O-ring seals for wear or for damage. If necessary, replace the O-ring seals.
Install O-ring seals (1) and (2) .End By: Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar parts catalog:
Parts core Caterpillar catalog:
4I1539
CORE
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311B, 311C, 311D LRR,...
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311B, 311C, 311D LRR,...
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311B, 311C, 311D LRR,...
1397944
CORE-COOLER
305.5, 306, 307B, 307C, 307D, 308C, 308D
305.5, 306, 307B, 307C, 307D, 308C, 308D
2070119
CORE AS-HEATER
308C, 314C, 321C
308C, 314C, 321C
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
1917547
CORE AS
305
305
318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
2070119
CORE AS-HEATER
308C, 314C, 321C
308C, 314C, 321C