2179638 CORE AS-RADIATOR Caterpillar parts
D7R II, D8R II
Rating:
Alternative (cross code) number:
CA2179638
217-9638
2179638
CA2179638
217-9638
2179638
Weight: 30 pounds 13 kg.
Information:
CORE DEPTH
119
mm
CORE WIDTH
144
mm
FIN HEIGHT
0
mm
FINS PER 25.4 MM
6
MODULE HEIGHT
867
mm
NUMBER OF ROWS
6
NUMBER OF TUBES
60
TRACK-TYPE TRACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2022-03-04
2022-03-04
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250522
Open door (4) .
Illustration 4 g01250523
Drain the water separator (8) into a container for storage or disposal. Disconnect hose (9). Disconnect harness assembly (10) .
Use Tooling (A) in order to remove water separator (8). Remove water separator (8) .
Disconnect hose assemblies (6) .
Remove bolts (5). Remove water separator base (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 5 g01250523
Position water separator base (7). Install bolts (5) .
Connect hose assemblies (6) .
Install water separator (8).
Connect harness assembly (10). Connect hose (9) .
Purge the air from the fuel system.
Illustration 6 g01250522
Close door (4) .
Illustration 7 g01250305
Turn valve (3) to the ON position.
Illustration 8 g01250304
Position sheet (2). Install bolts (1) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250522
Open door (4) .
Illustration 4 g01250523
Drain the water separator (8) into a container for storage or disposal. Disconnect hose (9). Disconnect harness assembly (10) .
Use Tooling (A) in order to remove water separator (8). Remove water separator (8) .
Disconnect hose assemblies (6) .
Remove bolts (5). Remove water separator base (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 5 g01250523
Position water separator base (7). Install bolts (5) .
Connect hose assemblies (6) .
Install water separator (8).
Connect harness assembly (10). Connect hose (9) .
Purge the air from the fuel system.
Illustration 6 g01250522
Close door (4) .
Illustration 7 g01250305
Turn valve (3) to the ON position.
Illustration 8 g01250304
Position sheet (2). Install bolts (1) .
Caterpillar parts catalog:
Parts core Caterpillar catalog:
3176C, 3196, 578, 583R, 583T, 587R, 587T, 980C, C-10, C-12, C11, C13, C15, C18, CX31-C13I, D8N, D8R, D8R II, D8T, PL83, PL87, R1600, R1600G, R1600H, R1700G, TH35-C11I, TH35-C13I
D7R II, D8R, D8R II
D10N, D10R, D6R, D6R II, D7R, D7R II, D8N, D8R, D8R II, D8T
D6R II, D7R II, D8R, D8R II
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 365B, 365B II, 365B L, 480, 572R II, 65E, 725, 730, 75D, 75E, 814F, 815F, 816F, 85D, 85E, 95E, 966G II, 972G II, C-10,...
16G, 16H NA, 245, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3456, 375, 375 L, 5080, 578, 583R, 587R, 589, 621E, 621F, 621G, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631D, 631E, 631G, 633E II, 6...
572R, 572R II, 583R, 587R, 621G, 623G, 627G, 657B, 966G II, 972G II, D10N, D10R, D6R, D6R II, D7R, D7R II, D8R, D8R II
120H, 120H ES, 120H NA, 135H, 135H NA, 140G, 572R, 572R II, D5E, D6R, D6R II, D6R III, D6T, D7R, D7R II
572R II, 583R, 587R, D7R, D7R II, D8R, D8R II
2348945
CORE AS-HYDRAULIC OIL COOLER
631G, 637G, D8R, D8R II, D9N
631G, 637G, D8R, D8R II, D9N
D7R II, D8R, D8R II
D8L, D8R II, D9N, D9R
D7R II, D8R, D8R II
1253945
CORE AS
D9R
D9R
D9R
816F, D9R
D8L, D9N, D9R
D10R, D9R
1887475
CORE AS-RADIATOR
D10R, D9R
D10R, D9R
24H, D10N, D10R, D8L, D9N, D9R