2562090 CORE AS-RADIATOR Caterpillar parts
D10N, D10R, D10T, D9R, D9T
Rating:
Alternative (cross code) number:
CA2562090
256-2090
2562090
CA2562090
256-2090
2562090
Weight: 40 pounds 18 kg.
TRACK-TYPE TRACTOR,
You can buy:
US$712.96
29 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 2562090 Folded Core Radiators for Models D10N/T, D9R, D9T
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
#US Replacement Part for Engine Oil Pressure Sensor & Filter Fit for GMC Buick Cadillac 12616646 cspart#2562090
Generic NOTE - Package included: 1 Set ONLY. Color: Silver
Generic NOTE - Package included: 1 Set ONLY. Color: Silver
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A (1) 9U-6198 Crankshaft Turning Tool 1
A (2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Start By:
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
This procedure must only be used to remove and install the main bearing shells with the crankshaft in position.The removal procedure and the installation procedure must be completed for each pair of main bearing shells before the next pair of main bearing shells are removed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01253717
Typical example
Remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the main bearing cap is marked for the correct location and orientation.
Illustration 2 g01253719
Typical example
Remove bolts (3) . Remove main bearing cap (4) from the cylinder block.
Illustration 3 g01253146
Typical example
Remove lower main bearing (5) from main bearing cap (4) . Keep the main bearing and the main bearing cap together. Take care not to displace dowels (6) .Note: The lower main bearing is a plain bearing that has no oil holes. The dowels may remain in the main bearing cap or in the cylinder block.
Illustration 4 g01253137
Typical example
For number three main bearing cap, remove thrust washers (7) .
Illustration 5 g01253142
Typical example
For number three main bearing, remove thrust washers (8) from the cylinder block. In order to remove the thrust washers, push the crankshaft toward the front of the engine or push the crankshaft toward the rear of the engine. Use Tooling (A) in order to rotate the crankshaft. If necessary, use a suitable tool to free the thrust washers.Note: Do not damage the machined surfaces of the crankshaft during removal of the thrust washers.
Illustration 6 g01253145
Table 1
Required Tools
Tool Part Number Part Description Qty
A (1) 9U-6198 Crankshaft Turning Tool 1
A (2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Start By:
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
This procedure must only be used to remove and install the main bearing shells with the crankshaft in position.The removal procedure and the installation procedure must be completed for each pair of main bearing shells before the next pair of main bearing shells are removed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01253717
Typical example
Remove allen head screws (1) . Remove bridge piece (2) .
Ensure that the main bearing cap is marked for the correct location and orientation.
Illustration 2 g01253719
Typical example
Remove bolts (3) . Remove main bearing cap (4) from the cylinder block.
Illustration 3 g01253146
Typical example
Remove lower main bearing (5) from main bearing cap (4) . Keep the main bearing and the main bearing cap together. Take care not to displace dowels (6) .Note: The lower main bearing is a plain bearing that has no oil holes. The dowels may remain in the main bearing cap or in the cylinder block.
Illustration 4 g01253137
Typical example
For number three main bearing cap, remove thrust washers (7) .
Illustration 5 g01253142
Typical example
For number three main bearing, remove thrust washers (8) from the cylinder block. In order to remove the thrust washers, push the crankshaft toward the front of the engine or push the crankshaft toward the rear of the engine. Use Tooling (A) in order to rotate the crankshaft. If necessary, use a suitable tool to free the thrust washers.Note: Do not damage the machined surfaces of the crankshaft during removal of the thrust washers.
Illustration 6 g01253145
Caterpillar parts catalog:
Parts core Caterpillar catalog:
572R, 572R II, 583R, 587R, 621G, 623G, 627G, 657B, 966G II, 972G II, D10N, D10R, D6R, D6R II, D7R, D7R II, D8R, D8R II
631D, 631G, 637G, 769D, 771D, 824C, 824G II, 825G II, D10N, D10R
834K, 836K, 988K, D8L, D9N, D9R, D9T
D8L, D9N, D9R
24H, D10N, D10R, D8L, D9N, D9R
D10T, D9R
D10N, D10R, D10T, D9L
D10N, D10R, D10T, D9T
D10N, D10R, D10T
D10N, D10R, D10T
D10T, D9R
D10R, D9R
1887475
CORE AS-RADIATOR
D10R, D9R
D10R, D9R
24H, D10N, D10R, D8L, D9N, D9R
1883989
CORE AS-RADIATOR
824G II, 826G II, D10T
824G II, 826G II, D10T
D11R, D11T
2289606
CORE AS-RADIATOR
D11R, D11T
D11R, D11T