2M0922 CORE ASSEM. Caterpillar parts
12E
Rating:
Alternative (cross code) number:
CA2M0922
2M-0922
2M0922
CA2M0922
2M-0922
2M0922
Weight: 0.010 pounds 0 kg.
MOTOR GRADER,
You can buy:
US$821.10
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Radiator 2M0922 for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R
HOMISIA Part number:CA2M0922, 2M-0922, 2M0922, CA7S1086, 7S-1086, 7S1086, CA8N7859, 8N-7859, 8N7859 || Application:for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R
HOMISIA Part number:CA2M0922, 2M-0922, 2M0922, CA7S1086, 7S-1086, 7S1086, CA8N7859, 8N-7859, 8N7859 || Application:for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R
2M0922 Engine Radiator Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R
GENERIC Part Name: Engine Radiator || Part Number:2M0922 || Application:Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R || Notice：Please be very careful to check our photos and part numbers, make sure the photos showed is the same as you wanted. || Service:If you are not satisfied with your purchase, contact us directly.
GENERIC Part Name: Engine Radiator || Part Number:2M0922 || Application:Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R || Notice：Please be very careful to check our photos and part numbers, make sure the photos showed is the same as you wanted. || Service:If you are not satisfied with your purchase, contact us directly.
2M0922 Engine Radiator Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R
GENERIC Part Name: Engine Radiator || Part Number:2M0922 || Application:Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R || Notice：Please be very careful to check our photos and part numbers, make sure the photos showed is the same as you wanted. || Service:If you are not satisfied with your purchase, contact us directly.
GENERIC Part Name: Engine Radiator || Part Number:2M0922 || Application:Fits for Caterpillar CAT Motor Grader 12E 120 120B Wheel Loader 920 930R || Notice：Please be very careful to check our photos and part numbers, make sure the photos showed is the same as you wanted. || Service:If you are not satisfied with your purchase, contact us directly.
Number on catalog scheme:
None
For full view, you need register
Compatible equipment models: 2M0922:
Information:
Removal Procedure
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Bellows assemblies MUST only be used once. Discard all bellows assemblies after use.
Illustration 1 g06088081
Disconnect latch mechanisms (1) and remove shield assembly (2).
Illustration 2 g06088096
Repeat Step 1 for shield assemblies (3).
Illustration 3 g06088131
Remove bolts (5) and bolt (6).
Remove shield (4)
Illustration 4 g06088139
Remove bolts (7) and shield (8).
Illustration 5 g06088150
Remove bolts (10).
Disconnect latch mechanisms (11) and remove shield assembly (9).
Illustration 6 g06091247
Disconnect latch mechanisms (13). Remove shields (12).
Illustration 7 g06091253
Remove shield (14).
Repeat Step 8 and Step 10 for the remaining shields.Note: Work in the direction indicated by the arrow in Illustration 6.Note: Attach suitable rigid support to exhaust manifolds prior to removal. The rigid support will allow removal of exhaust manifolds (17) without disruption of the bellows joints.
Illustration 8 g06088396
Loosen clamps (15).
Attach a suitable lifting device onto exhaust manifolds (17). The weight of exhaust manifolds (17) is approximately 48 kg (105 lb).Note: The joint between inlet manifold (18) and the exhaust manifold is not serviceable. Do not loosen or remove bolts (19) when the exhaust manifold, the inlet manifold, the bellows, or the turbochargers are serviced.
Illustration 9 g06088425
Remove bolts (21) and the washers from exhaust manifolds (17). Loosen bolts (20). If necessary, remove temperature sensor adapter (22) and the thermowell.
Illustration 10 g06088436
Loosen clamps (24), clamps (25), and clamps (26). Rotate turbine housing (23) away from bellows (27).Note: All clamps are designed for one time usage must be discarded.
Remove exhaust manifold (17).
Remove inlet manifold (18), exhaust manifold (18), and the bellows together.
Repeat Step 1 through Step 15 for the opposite side.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
Clamp assemblies MUST only be used once. Discard all clamp assemblies after use.
Bellows assemblies MUST only be used once. Discard all bellows assemblies after use.
Illustration 1 g06088081
Disconnect latch mechanisms (1) and remove shield assembly (2).
Illustration 2 g06088096
Repeat Step 1 for shield assemblies (3).
Illustration 3 g06088131
Remove bolts (5) and bolt (6).
Remove shield (4)
Illustration 4 g06088139
Remove bolts (7) and shield (8).
Illustration 5 g06088150
Remove bolts (10).
Disconnect latch mechanisms (11) and remove shield assembly (9).
Illustration 6 g06091247
Disconnect latch mechanisms (13). Remove shields (12).
Illustration 7 g06091253
Remove shield (14).
Repeat Step 8 and Step 10 for the remaining shields.Note: Work in the direction indicated by the arrow in Illustration 6.Note: Attach suitable rigid support to exhaust manifolds prior to removal. The rigid support will allow removal of exhaust manifolds (17) without disruption of the bellows joints.
Illustration 8 g06088396
Loosen clamps (15).
Attach a suitable lifting device onto exhaust manifolds (17). The weight of exhaust manifolds (17) is approximately 48 kg (105 lb).Note: The joint between inlet manifold (18) and the exhaust manifold is not serviceable. Do not loosen or remove bolts (19) when the exhaust manifold, the inlet manifold, the bellows, or the turbochargers are serviced.
Illustration 9 g06088425
Remove bolts (21) and the washers from exhaust manifolds (17). Loosen bolts (20). If necessary, remove temperature sensor adapter (22) and the thermowell.
Illustration 10 g06088436
Loosen clamps (24), clamps (25), and clamps (26). Rotate turbine housing (23) away from bellows (27).Note: All clamps are designed for one time usage must be discarded.
Remove exhaust manifold (17).
Remove inlet manifold (18), exhaust manifold (18), and the bellows together.
Repeat Step 1 through Step 15 for the opposite side.Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
Caterpillar parts catalog:
Parts core Caterpillar catalog:
120, 120G, 12E, 12F, 140, 14E, 2470C, 2570C, 2670C, 2864C, 414E, 416, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 426, 426B, 426C, 428, 428B, 428D, 428E, 430D, 430E, 430F, 432D, 432E, ...
12E, 3306, 941, 950, 955H, D4D, D5, D6C, D7F
2M2773
CORE ASSEM.
12E, 651, 657, 955C, 977D, D320A, D326F, D337F, D342, D342C, D353C, D375D, D8H
12E, 651, 657, 955C, 977D, D320A, D326F, D337F, D342, D342C, D353C, D375D, D8H
12E, 14E
2D3969
CORE
12E
12E
9D7929
CORE
120G, 12G
120G, 12G
12G, 130G, 16G
1P6040
CORE
16
16
2D2638
CORE
12F
12F
5D0879
CORE
16
16
330, 330 FM L, 330 L
330, 330 FM L, 330 L
120B
2D3969
CORE
12E
12E