2W7701 CORE AS-HYDRAULIC OIL Caterpillar parts
926, 926A, 936, 936F, IT18, IT18B, IT28, IT28B
Rating:
Alternative (cross code) number:
CA2W7701
2W-7701
2W7701
CA2W7701
2W-7701
2W7701
Weight: 44 pounds 19 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compatible equipment models: 2W7701:
For full view, you need register
Information:
1. Remove shaft (2). Remove pin (1) from shaft.2. Remove pins (3) from the flyweights. Remove flyweights (4). 3. Remove ring, races (6) and bearing from the riser (follower) (5). 4. Remove cover (7) and spring (8) from governor housing. There is force on the cover from the spring.5. Remove seal (9) from cover.6. Remove cover (10) for the low and high idle adjustments. 7. Remove locknut and screw (13) for the high idle adjustment.8. Remove bolt (15) and washers for the low idle adjustment.9. Remove spring (16) and guide.10. Remove pin (14) and plate (11).11. Remove shaft (12) from the housing. 12. Remove pin (18) and two spacers (17) from shaft. 13. Remove shaft (19) from the governor housing.14. Remove washer (20) and levers (21) and (22) from governor housing. 15. Remove cover (23) from governor housing. 16. Remove seal (25) and bearing.17. Remove seals (24) and (26) from governor housing.Assemble Governor
1. Install bearing and seal in the housing with tool (A). The lip of the seal must be toward the bearing.2. Install seal (1) in housing with tool (A). The lip of seal must be toward inside of housing.3. Install seal (2) in housing with tooling (B). The lip of seal must be toward the inside of housing. 4. Install shaft (3) in the housing. 5. Install plates (4), spacers (8) and pin (7) on shaft.6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and guide.10. Install bolts (12) and washer for low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push plate and pin (11) over toward the bolt (12) and tighten the bolt.12. Install seal in cover with tooling (B). The lip of seal must be toward the inside. 13. Install spring (15) in the cover. Install cover (14) on housing.
The spring (15) must be installed with the end of spring as shown.
14. Install cover (16) for the idle adjustment screws. 15. Install bearing (19) between the races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.end by:a) connection of governor to fuel injection pump housing
1. Install bearing and seal in the housing with tool (A). The lip of the seal must be toward the bearing.2. Install seal (1) in housing with tool (A). The lip of seal must be toward inside of housing.3. Install seal (2) in housing with tooling (B). The lip of seal must be toward the inside of housing. 4. Install shaft (3) in the housing. 5. Install plates (4), spacers (8) and pin (7) on shaft.6. Install shaft (5) in housing and through washer (9) and levers (6). 7. Install pin (11) in holes of the plates.8. Install screw (10) and locknut for high idle adjustment.9. Install spring (13) and guide.10. Install bolts (12) and washer for low idle adjustment.
After the fuel injection pump housing and governor have been installed on the engine, make an adjustment for the high and low idle. See GOVERNOR ADJUSTMENT as shown in TESTING AND ADJUSTING.
11. Push plate and pin (11) over toward the bolt (12) and tighten the bolt.12. Install seal in cover with tooling (B). The lip of seal must be toward the inside. 13. Install spring (15) in the cover. Install cover (14) on housing.
The spring (15) must be installed with the end of spring as shown.
14. Install cover (16) for the idle adjustment screws. 15. Install bearing (19) between the races (18) on riser (follower) (17). Install ring (20) that holds the washers on the riser (follower). 16. Install pin in shaft (23).17. Install flyweights (22) and pin (21).18. Install shaft (23) in the flyweight assembly.end by:a) connection of governor to fuel injection pump housing
Caterpillar parts catalog:
Parts core Caterpillar catalog:
120, 120G, 12E, 12F, 140, 14E, 2470C, 2570C, 2670C, 2864C, 414E, 416, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 424D, 426, 426B, 426C, 428, 428B, 428D, 428E, 430D, 430E, 430F, 432D, 432E, ...
7E3328
CORE AS
916, 926, 936, D4H, D4HTSK II, G916, G936, IT28B
916, 926, 936, D4H, D4HTSK II, G916, G936, IT28B
916, 926, 936, 936F, D4H, D4H XL, D4HTSK II, D4HTSK III, G936, IT28B
8N6536
CORE AS-OIL COOLER
508, 926A, D3B, D4H, D4H XL, D4HTSK II, D4HTSK III, IT28
508, 926A, D3B, D4H, D4H XL, D4HTSK II, D4HTSK III, IT28
916, 926, 926A, 936, CS-643, D3B, D4H, D4HTSK II, G936, IT28
2W8781
CORE AS-CONDENSER
926, 936, D4H, G936, IT28
926, 936, D4H, G936, IT28
7E8216
CORE AS-CONDENSER
916, 926, D4H, D4HTSK II, IT28B
916, 926, D4H, D4HTSK II, IT28B
7E3145
CORE AS-CONDENSER
936, 936F, D4H
936, 936F, D4H
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
926, 936, D4H, G926, IT18B, IT28B
517, 936F
926, 936, D4H, G926, IT18B, IT28B
613C, 613C II, 615C, 793C, 815B
9J1008
CORE AS-OIL COOLER
613, 613B, 613C, 613C II
613, 613B, 613C, 613C II
621E, 623E, 627E, 631D, 631E, 637D, 637E, 657E
928F, 938F, IT28F, IT38F
2626904
CORE AS-OIL COOLER
613C II
613C II
2Y8913
CORE AS
631E
631E
7C2066
CORE AS
615, 615C
615, 615C
7W8193
CORE AS-OIL COOLER
621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E
621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E
7W0675
CORE AS-OIL COOLER
621E, 627E, 627F, 627G, 637E, 637G, D11N, D11R
621E, 627E, 627F, 627G, 637E, 637G, D11N, D11R