3382217 CORE AS-RADIATOR Caterpillar parts
D11T
Rating:
Alternative (cross code) number:
CA3382217
338-2217
3382217
CA3382217
338-2217
3382217
Weight: 267 pounds 121 kg.
TRACK-TYPE TRACTOR,
Compatible equipment models: 3382217:
Information:
Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     2P-5518     Bearing Tool     1    Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Check the main bearing caps for identification of the location and check the direction of the main bearing caps in relation to the cylinder block. The main bearing caps must be installed in the original location and the original direction.
Illustration 1 g00503084
Remove No. 2 through No. 6 main bearing caps (1). Remove the thrust plates from the No. 4 main bearing. Note: Remove No. 1 and No. 7 main bearing caps (1) after No. 2 through No. 6 main bearing caps have been installed.
Illustration 2 g00503174
Note: If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft. Turn the crankshaft so that the bearing tab is rotated out of the crankshaft.
Remove the upper halves of the main bearings by putting Tooling (A) in oil hole (2) in the crankshaft. Turn the crankshaft in the direction which will remove the upper halves of the main bearings.
Remove the lower halves of the main bearings from the main bearing caps.
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     2P-5518     Bearing Tool     1    Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Check the main bearing caps for identification of the location and check the direction of the main bearing caps in relation to the cylinder block. The main bearing caps must be installed in the original location and the original direction.
Illustration 1 g00503084
Remove No. 2 through No. 6 main bearing caps (1). Remove the thrust plates from the No. 4 main bearing. Note: Remove No. 1 and No. 7 main bearing caps (1) after No. 2 through No. 6 main bearing caps have been installed.
Illustration 2 g00503174
Note: If the crankshaft is turned in the wrong direction, the tab on the bearing will be pushed between the crankshaft and the bearing area of the cylinder block. This can result in damage to the cylinder block and/or the crankshaft. Turn the crankshaft so that the bearing tab is rotated out of the crankshaft.
Remove the upper halves of the main bearings by putting Tooling (A) in oil hole (2) in the crankshaft. Turn the crankshaft in the direction which will remove the upper halves of the main bearings.
Remove the lower halves of the main bearings from the main bearing caps.
Caterpillar parts catalog:
Parts core Caterpillar catalog:
7C0145
CORE AS-OIL COOLER
24H, 3412, 3412C, 3412D, 3412E, 374F L, 385C, 390F L, 5110B, 651E, 657E, 657G, 770G, 770G OEM, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC,...
24H, 3412, 3412C, 3412D, 3412E, 374F L, 385C, 390F L, 5110B, 651E, 657E, 657G, 770G, 770G OEM, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC,...
3582305
CORE AS-OIL COOLER
C15, C18, C27, C32, CX31-C18I, CX35-C18I, D10T2, D11T
C15, C18, C27, C32, CX31-C18I, CX35-C18I, D10T2, D11T
3381924
CORE AS-OIL COOLER
D11R, D11T
D11R, D11T
3729124
CORE AS-OIL COOLER
824K, 825K, 826K, 834K, 836K
824K, 825K, 826K, 834K, 836K
3343321
CORE AS-HYDRAULIC OIL COOLER
D8T, D9T
D8T, D9T
3353416
CORE AS-AFTERCOOLER
D7E, D7E LGP
D7E, D7E LGP
3353415
CORE AS-RADIATOR
D7E, D7E LGP
D7E, D7E LGP
3935047
CORE AS-RADIATOR
D10T2
D10T2