3R2605 CORE ASSEM. Caterpillar parts
D7F
Rating:
Alternative (cross code) number:
CA3R2605
3R-2605
3R2605
CA3R2605
3R-2605
3R2605
Weight: 308 pounds 139 kg.
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 3R2605 Core Radiators for Models D7F
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
CTP 3R2605 Core Radiators for Models D7F
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
CTP Reduce the cost of radiator repairs || Provide superior performance || Improved resistance
Number on catalog scheme:
35
For full view, you need register
Compatible equipment models: 3R2605:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B 9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C 4C-9507 Retaining Compound - Start By:
Remove the electronic unit injectors.
Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
Illustration 1 g01261663
Install Tooling (A) into electronic unit injector sleeve (1).
Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head assembly.
Illustration 2 g01860393
Remove electronic unit injector sleeve (1). Installation Procedure
Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris.
Illustration 3 g01261773
Install new O-ring seals (2) and (3) on electronic unit injector sleeve (1). Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the electronic unit injector sleeve only.
Apply a thin coat of Tooling (C) to O-ring seal (3) and the contact surface of electronic unit injector sleeve (1) on the surface that is Marked "X".
Illustration 4 g01261802
Install Tooling (A) into the threads of electronic unit injector sleeve (1).
Position Tooling (A) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seal on the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head.
Use Tooling (A) and a hammer to install electronic unit injector sleeve (1) in the cylinder head.
Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures. End By:
Install the electronic unit injectors.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B 9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C 4C-9507 Retaining Compound - Start By:
Remove the electronic unit injectors.
Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
Illustration 1 g01261663
Install Tooling (A) into electronic unit injector sleeve (1).
Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head assembly.
Illustration 2 g01860393
Remove electronic unit injector sleeve (1). Installation Procedure
Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris.
Illustration 3 g01261773
Install new O-ring seals (2) and (3) on electronic unit injector sleeve (1). Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the electronic unit injector sleeve only.
Apply a thin coat of Tooling (C) to O-ring seal (3) and the contact surface of electronic unit injector sleeve (1) on the surface that is Marked "X".
Illustration 4 g01261802
Install Tooling (A) into the threads of electronic unit injector sleeve (1).
Position Tooling (A) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seal on the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head.
Use Tooling (A) and a hammer to install electronic unit injector sleeve (1) in the cylinder head.
Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures. End By:
Install the electronic unit injectors.
Caterpillar parts catalog:
Parts core Caterpillar catalog:
3306, 637D, 966C, 977K, D6C, D6D, D7F
9S6157
CORE ASSEM.
824B
824B
2P6111
CORE ASSEM.
814, 815
814, 815
