CORE AS-RADIATOR 4P8530 - Caterpillar

4P8530 CORE AS-RADIATOR Caterpillar parts 816B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4P8530
4P-8530
4P8530

Weight: 347 pounds 157 kg.

Information:

CORE DEPTH 150.8 mm

CORE HEIGHT 1087 mm

CORE WIDTH 1031.9 mm

FINS PER 25.4 MM 5

NUMBER OF TUBE ROWS 8

TUBE CONFIGURATION CANTED

Buy CORE AS-RADIATOR 4P8530 Caterpillar genuine, new aftermarket tractor parts with delivery
LANDFILL COMPACTOR,

Compatible equipment models: 4P8530:

LANDFILL COMPACTOR 816B Caterpillar

For full view, you need register

Information:

that replacement of the ECM is necessary prior to replacement of the ECM. The ECM is seldom the cause of a diagnostic code. Always check that the proper ground and power are available to the ECM. Before replacing ECM, it is recommended that dealer service staff contact the ECM Hotline help desk. The ECM Hotline will provide guidance to determine if an ECM needs replaced. Dealer Technical Communicators have contact information for the ECM Hotline. Note: New electronic control modules are available either pre-programmed for a particular machine or the ECM is not programmed. An ECM that has not been programmed must be programmed by using the Caterpillar Electronic Technician (ET). See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program". See item 6 in order to determine whether the ECM has been programmed.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the ECM.
Remove the ECM.
Ensure that the replacement ECM has the correct part number.
Connect the machine harness to the ECM.
Determine whether the ECM has been programmed. Connect the Caterpillar Electronic Technician (ET) to the service tool connector. The ET communicates to the ECM.The ET will indicate whether the ECM has been programmed. An ECM that has not been programmed must be programmed by using the WinFlash software which is contained in the ET. See Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program".The ET will provide access to the ECM, if the ECM has already been programmed.Note: Some Variations in the ET menu may be experienced. View the proper subject for information about a specific ET menu.Note: Performance will be affected by ANY calibration procedures that are omitted. Make sure that all calibration procedures are performed. Perform all calibration procedures, even if the replacement ECM was acquired from a similar machine.Note: The profile of the operator will be lost when the ECM is replaced.

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

816B LANDFILL COMPACTOR 15Z00001-UP (MACHINE) POWERED BY 3306 ENGINE

9Y-0984: CONVERSION GP-RADIATOR » CORE AS-RADIATOR SEBP13430094

Parts core Caterpillar catalog:

7N0110 CORE AS-ENGINE OIL COOLER
143H, 14H NA, 160H ES, 160H NA, 163H NA, 1673C, 235C, 235D, 330 FM L, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 330B, 350, 627B, 627E, 627F, 637E, 639D, 65, 65C, 816B, 966F II, 966G, 970F, 972G, 973, 97...

7W0491 CORE AS-AFTERCOOLER
140H, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235B, 330, 330 L, 3306, 3306B, 330B, 330B L, 545, 572R, 611, 615, 615C, 627B, 627E, 627F, 627G, 637D, 637E, 637G, 639D, 65, 65C, 814F, 815F,...

8N6943 CORE AS-HYDRAULIC OIL COOLER
613C, 615, 793B, 814B, 816B, 85C, 85D, 963, 973

2W5540 CORE AS-RADIATOR
16G, 16H, 16H NA, 3406B, 3408, 3412, 572G, 578, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 793C, 814B, 815B, 816B, 966D, D6H, D6H II, D7G, D7H, D8N, G3406

1275537 CORE AS
235B, 572R, 769C, 769D, 771C, 771D, 814B, 814F, 815B, 815F, 816B, 816F, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 972G, AD40, AD45, AE40, AE40 II, C-9, C9, C9.3, CX31-C9I, D6H, D6H XL, D6H XR, D...