5S0602 CORE ASSEM. Caterpillar parts
621, 621E, 621R, 623
Rating:
Alternative (cross code) number:
CA5S0602
5S-0602
5S0602
CA5S0602
5S-0602
5S0602
Weight: 275 pounds 124 kg.
Information:
CORE DEPTH
150.876
mm
CORE HEIGHT
990.6
mm
CORE WIDTH
754.126
mm
FINS PER 25.4 MM
9
NUMBER OF TUBE ROWS
8
TUBE CONFIGURATION
CANTED
WHEEL SCRAPER, WHEEL TRACTOR,
Number on catalog scheme:
42
For full view, you need register
Information:
System Introduction
The OMM documentation should be consulted in order to determine the type of WAVS that is installed upon the machine.Power is supplied to the system when the operator turns the key switch to the ON position. The power On/Off button that is on the display may be disabled.The display will perform a self-test after power is applied. The self-test will last approximately 8 seconds. Each indicator LED on the display will blink once as the self-test is executed. If the system passes the self-test, then the view of a camera will appear on the display.As stated in the "Configuration" section of this document, "Manual" mode has been disabled for use in single camera systems. However, "Manual" mode is available for multi camera systems.Refer to the "Configuration" section of this document for information about the process in order to enable the "Manual" mode if needed.Safety
In order to perform some of the procedures that are listed in the "Troubleshooting" section, it will be necessary to follow the safety procedures that are listed in the "Systems Operation General Information - Safety" section. In addition to the "Systems Operation General Information - Safety" section information, in order to gain safe access to the WAVS components that are toward the rear of the machine, for example, in an Off Highway Truck (OHT), the bed of the truck will have to be raised and the safety cable installed. Refer to Illustration 1.
Illustration 1 g01181619
Safety Cable Installed for Truck Bed.
The OMM documentation should be consulted in order to determine the type of WAVS that is installed upon the machine.Power is supplied to the system when the operator turns the key switch to the ON position. The power On/Off button that is on the display may be disabled.The display will perform a self-test after power is applied. The self-test will last approximately 8 seconds. Each indicator LED on the display will blink once as the self-test is executed. If the system passes the self-test, then the view of a camera will appear on the display.As stated in the "Configuration" section of this document, "Manual" mode has been disabled for use in single camera systems. However, "Manual" mode is available for multi camera systems.Refer to the "Configuration" section of this document for information about the process in order to enable the "Manual" mode if needed.Safety
In order to perform some of the procedures that are listed in the "Troubleshooting" section, it will be necessary to follow the safety procedures that are listed in the "Systems Operation General Information - Safety" section. In addition to the "Systems Operation General Information - Safety" section information, in order to gain safe access to the WAVS components that are toward the rear of the machine, for example, in an Off Highway Truck (OHT), the bed of the truck will have to be raised and the safety cable installed. Refer to Illustration 1.
Illustration 1 g01181619
Safety Cable Installed for Truck Bed.
Caterpillar parts catalog:
Parts core Caterpillar catalog:
621, 621E, 621R, 623, 980B
9M9481
CORE ASSEM.
657, 657B
657, 657B
1S0250
CORE ASSEM.
657, 657B
657, 657B
7S8801
CORE ASSEM.
657, 666
657, 666
8S6543
CORE ASSEM.
641B
641B
641B
9S3767
CORE ASSEM.
627, 637B
627, 637B
8S0126
CORE ASSEM.
621, 621B, 627
621, 621B, 627