4766881 COUPLER AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA4766881
476-6881
4766881
CA4766881
476-6881
4766881
Weight: 159 pounds 72 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Brake X Rear Left Wheel Bearing for 1988 Audi 80 Quattro | HC Series Rear Driver Wheel Bearings
Brake X Get The Right Fit: The Brake X automotive replacement bearings are built for 1988 80 Quattro Brake Non-ABS || We Stand Behind Your Every Stop: Your wheel bearings is the most essential part that holds your vehicle's wheels in place. Unusual noise from brakes, wheel or steering vibrations are usual signs of faulty hub bearing assembly, The Brake X solution is simple. We provide OE quality wheel bearing for your vehicle as your usual trustable solution. || The Solution: The Brake X wheel bearing comes pre-lubricated and ready to install. They are direct replacements for your original parts, no extra modifications are required. || OE+ Quality: The Brake X bearings assembly are precisely engineered to meet OE level specifications such as axial and radial load capacities. || Lifetime Warranted: The Brake X wheel bearing comes with comes with our limited lifetime warranty against manufacturing defects.
Brake X Get The Right Fit: The Brake X automotive replacement bearings are built for 1988 80 Quattro Brake Non-ABS || We Stand Behind Your Every Stop: Your wheel bearings is the most essential part that holds your vehicle's wheels in place. Unusual noise from brakes, wheel or steering vibrations are usual signs of faulty hub bearing assembly, The Brake X solution is simple. We provide OE quality wheel bearing for your vehicle as your usual trustable solution. || The Solution: The Brake X wheel bearing comes pre-lubricated and ready to install. They are direct replacements for your original parts, no extra modifications are required. || OE+ Quality: The Brake X bearings assembly are precisely engineered to meet OE level specifications such as axial and radial load capacities. || Lifetime Warranted: The Brake X wheel bearing comes with comes with our limited lifetime warranty against manufacturing defects.
This part in 10 request:
Show.
This information for suppliers only!
2024-12-31
2023-10-06
2023-01-17
2022-09-22
2022-08-02
2022-08-02
2022-05-22
2022-04-20
2021-10-16
2021-09-10
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Bolt
1 - 14 NF by 8 inch 2
C 5F-4764 Pry Bar 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the magnetic pickups.
Illustration 1 g00911678
Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb).
Remove two bolts (2) on each side of the crankshaft.
Install Tooling (B).
Remove remaining bolts (2).
Remove flywheel (1). Use the following procedure if flywheel (1) is not easily separated from the crankshaft:
Install Tooling (A) in each side of flywheel (1).
Use Tooling (C) to remove flywheel (1) from the crankshaft. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Bolt
1 - 14 NF by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the condition of the ring gear. Use the following procedure in order to replace the ring gear, if necessary.
Remove the damaged ring gear from the flywheel.
Raise the temperature of the new ring gear.
Install the ring gear on the flywheel. Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor.
Illustration 2 g00911678
Install Tooling (B) in the end of the crankshaft.
Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb). Note: Ensure that the mark on flywheel (1) is aligned with the mark on the crankshaft.
Lift flywheel (1) into position onto Tooling (B).
Apply clean engine oil to bolts (2) and install bolts (2).
Remove Tooling (A) and Tooling (B). Install remaining two bolts (2). Tighten bolts (2) to a torque of 1150 60 N m (850 44 lb ft).
Install the magnetic pickups and adjust.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Bolt
1 - 14 NF by 8 inch 2
C 5F-4764 Pry Bar 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the magnetic pickups.
Illustration 1 g00911678
Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb).
Remove two bolts (2) on each side of the crankshaft.
Install Tooling (B).
Remove remaining bolts (2).
Remove flywheel (1). Use the following procedure if flywheel (1) is not easily separated from the crankshaft:
Install Tooling (A) in each side of flywheel (1).
Use Tooling (C) to remove flywheel (1) from the crankshaft. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B - Guide Bolt
1 - 14 NF by 8 inch 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the condition of the ring gear. Use the following procedure in order to replace the ring gear, if necessary.
Remove the damaged ring gear from the flywheel.
Raise the temperature of the new ring gear.
Install the ring gear on the flywheel. Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor.
Illustration 2 g00911678
Install Tooling (B) in the end of the crankshaft.
Attach Tooling (A) and a suitable lifting device to flywheel (1). The weight of flywheel (1) is approximately 170 kg (375 lb). Note: Ensure that the mark on flywheel (1) is aligned with the mark on the crankshaft.
Lift flywheel (1) into position onto Tooling (B).
Apply clean engine oil to bolts (2) and install bolts (2).
Remove Tooling (A) and Tooling (B). Install remaining two bolts (2). Tighten bolts (2) to a torque of 1150 60 N m (850 44 lb ft).
Install the magnetic pickups and adjust.
Caterpillar parts catalog:
Parts coupler Caterpillar catalog:
4755066
COUPLER AS-QUICK
Caterpillar
Caterpillar
4738544
COUPLER AS-QUICK
Caterpillar
Caterpillar
4738542
COUPLER GP-QUICK
Caterpillar
Caterpillar
4738536
COUPLER GP-QUICK
Caterpillar
Caterpillar
4736959
COUPLER AS
Caterpillar
Caterpillar
4727836
COUPLER
Caterpillar
Caterpillar
4834040
COUPLER GP-QUICK
Caterpillar
Caterpillar
4834029
COUPLER GP-QUICK
Caterpillar
Caterpillar
4832398
COUPLER GP-QUICK
Caterpillar
Caterpillar
4798959
COUPLER AS
Caterpillar
Caterpillar
4798958
COUPLER AS
Caterpillar
Caterpillar
4779674
COUPLER AS
Caterpillar
Caterpillar