AVSPARE.COM
parts catalog

COUPLING ASSEM. 2H9272 - Caterpillar



2H9272 COUPLING ASSEM. Caterpillar parts 41, 44 COUPLING
Rating:
25
Alternative (cross code) number:
CA2H9272
2H-9272
2H9272
Caterpillar 2H9272 COUPLING ASSEM.
Weight: 0.50 pounds 0 kg.

Buy COUPLING ASSEM. 2H9272 Caterpillar genuine, new aftermarket tractor parts with delivery
HYDRAULIC CONTROL,

Compatible equipment models: 2H9272:

HYDRAULIC CONTROL  41   44   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Before doing any service work which requires separating track, a through inspection of the front track roller frame must be made. See Special Instruction, Form No. SMHS8273-02
Start By:a. separation of track 1. Use tooling (A) to lift the front and rear of the tractor, and install tooling (B). There will be a loss of oil when retainer (1) is removed.2. Remove the bolts and retainer (1) from the roller frame. 3. Remove O-ring seal (2) from retainer (1). 4. Fasten a hoist to track roller frame (3) as shown. 5. Install steel shims at location (X) between the equalizer bar and the main frame to keep the equalizer bar in its original position when the track roller frame is removed. It may be necessary to use the hoist to raise or lower the track roller frame until pin assembly (4) can be removed.6. Remove bolt (5). Remove pin assembly (4) from the track roller frame. 7. Remove three bolts (6) and plate (7) that holds the track roller frame in position on the pivot shaft.8. Use the hoist, and remove the track roller frame from the machine. The weight of the track roller frame is 930 kg (2050 lb). 9. If necessary, remove bearings (8) from the track roller frame. 10. Remove seal (10) from pivot shaft (9).Install Track Roller Frames
1. Install seal (2) on pivot shaft (1). Install the seal with the larger diameter toward the outside of the machine. 2. If the bearings were removed from the track roller frame, lower the temperature of the bearings.3. Use tooling (A) to install the inside bearing (3) until it is seated in the track roller frame. The inside diameter must be 88.744 0.084 mm (3.4939 .0033 in) after installation.4. Use tooling (B) to install the outside bearing (4) until it is seated in the track roller frame. The inside diameter of the bearing must be 69.856 0.134 mm (2.7502 .0053 in). 5. Fasten a hoist to track roller frame (6) as shown. Put the track roller frame in position on the pivot shaft. Install retainer (5) and the bolts to hold the track roller frame in place on the pivot shaft. 6. Align the track roller frame with the equalizer bar, and install pin assembly (7).7. Install bolt (8) to hold pin assembly (7) in position.8. Remove the shims at location (X) between the equalizer bar and the main frame. 9. Install O-ring seal (10) on retainer (9). Put clean oil on the O-ring seal. 10. Install retainer (9) on the track roller frame. 11. Use tooling (C) to lift the machine from tooling (D). Remove tooling (D), and lower the machine to the ground.12. Fill the pivot shaft compartment with oil to the correct level. See the Maintenance Guide.End By:a. connection of tracks

Caterpillar parts catalog:

Caterpillar parts catalog
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 44 HYDRAULIC CONTROL 06W05001-UP
NO. 44 HYDRAULIC CONTROL 07W00001-UP
NO. 44 HYDRAULIC CONTROL 09W00001-UP
141, 143, 161, 181 & 191 HYD. CONTROLS 36F00001-00413
140 & 150 HYDRAULIC CONTROL 22J00001-UP
141, 143, 151 & 161 HYDRAULIC CONTROL 54G00001-UP


Parts coupling Caterpillar catalog:

7G6229 COUPLING
931B, D3B, D5C
7T1682 COUPLING AS
931B, D3B, D3C II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.