AVSPARE.COM
parts catalog

COUPLING GP-TORSIONAL 3474034 - Caterpillar


3474034 COUPLING GP-TORSIONAL Caterpillar parts 924K
Rating:
51
Alternative (cross code) number:
CA3474034
347-4034
3474034
Caterpillar 3474034 COUPLING GP-TORSIONAL

Buy COUPLING GP-TORSIONAL 3474034 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3474034:

WHEEL LOADER  924K   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:


Illustration 5 g01512236
Single phase two-wire (double delta)Transformer Connections
In order to monitor the generator output voltages greater than 600 V, potential transformers must be used.Note: The EMCP 3 must be programmed when connecting external potential transformers.ReferenceSystems Operation, RENR7902, "Setpoint Programming" and Testing and Adjusting, "Electronic Control Module (Generator Set) - Configure".Note: The wye configuration of external potential transformers is preferred for 4-wire wye generators. The preference is due to the greater accuracy when loads are unbalanced. With the open delta configuration, some power parameters cannot be determined. The parameters are real power phase A, B, C, and power factor phase A, B, C. For maximum accuracy, the open delta configuration of external potential transformers should be used only for 3-wire delta generators.
Illustration 6 g01228369
Wye configuration with external potential transformers for the 4-wire wye generatorThe wye configuration allows the accurate measurement of all power parameters by the EMCP 3. Accurate measurement is possible even when the loads are unbalanced and neutral current is present. All power parameters are shown on the display of the EMCP 3. The EMCP 3 configuration parameter" Generator Connection Configuration" must be set to wye or star.
Illustration 7 g01228370
Open delta configuration of external potential transformers for the 3-wire delta generatorNote: The open delta configuration for 3-wire delta generators allows the accurate measurement of power parameters by the EMCP 3. Accurate measurement is possible even when the loads are unbalanced and circulating current is present. The real power phase A, B, and C cannot be determined. The power factor phase A, B, and C cannot be determined. The phases are not shown on the EMCP 3 display. The EMCP 3 configuration parameter "Generator Connection Configuration" must be set to "delta 3-wire".
Illustration 8 g01228371
Open delta configuration of external potential transformers on the 4-wire wye generatorNote: The open delta configuration for 4-wire wye generators results in less accurate measurement of all power parameters by the "EMCP 3". The open delta configuration results in less accurate measurement when the loads are unbalanced and neutral current is present. Real power phase A, B, C and power factor phase A, B, C cannot be determined and are not shown on the "EMCP 3" display. The EMCP 3 configuration parameter "Generator Connection Configuration" must be set to "delta 3-wire".On 4-wire wye generators, three separate potential transformers are required for accurate power metering unless the loads are completely and continually balanced. Even if the loads are balanced, some power parameters cannot be determined. Real power phase A, B, C, and power factor phase A, B, C are not shown on the EMCP 3 display.On 3-wire delta generators, two potential transformers allow maximum accuracy for all load conditions. Real power phase A, B, C and power factor phase A, B, C cannot be determined and are not shown on the EMCP 3 display.
Table 1
Transformer Connections    
Parameter     Star     3-WIRE DELTA     4-WIRE DELTA     2-WIRE 1-PHASE     3-WIRE 1-PHASE    
Generator Frequency

Caterpillar parts catalog:

Caterpillar parts catalog
924K Wheel Loader PWR00001-UP (MACHINE) POWERED BY C6.6 Engine
924K Small Wheel Loader ENC00001-UP (MACHINE) POWERED BY C7.1 Engine
924K Small Wheel Loader HJF00001-UP (MACHINE) POWERED BY C7.1 Engine
926M Small Wheel Loader LTE00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts coupling Caterpillar catalog:

8S7169 COUPLING
10 FT, 10-20B, 215, 215D, 225, 225D, 227, 229, 229D, 231D, 235, 235C, 245, 245B, 24H, 3116, 325B L, 325C, 325D L, 330B L, 330C, 330D L, 336D L, 3406E, 345B II, 345B L, 345C L, 365B, 365B II, 365C, 365...
2183745 COUPLING
924K, 930K, 938G II, 938K, 950G II, 962G II, IT38G II, IT62G II
4391588 COUPLING
924G, 924H, 924K, 930G, 930K, 938K
4391589 COUPLING AS
924G, 924H, 924K, 930G, 930K, 938K
1773489 COUPLING AS
924K, 930K, 938K, 950G II, 950H, 962G II, 962H, 966G II, 966H, 966K, 966M, 966M XE, 972G II, 972H, 972K, 972M, 972M XE, 980G II, 980H, 980K, 980M, 982M, 986H
1782716 COUPLING
924K, 930K, 938K, 950G II
2211583 COUPLING
725, 725C, 730, 730C, 735, 735B, 740, 740B, 924K, 930K, 938K, D11T
3738459 COUPLING-SHAFT
924K, 930K, 938K, 993K
1669266 COUPLING
924K, 930K, 938K
3109497 COUPLING GP-FLEXIBLE
336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 568 FM LL
1023829 COUPLING GP-PUMP
315, 315B, 315B FM L, 317B LN
2666305 COUPLING GP-FLEXIBLE
385C, 385C FS, 385C L, 385C L MH
2228350 COUPLING GP-PUMP
365C, 365C L, 365C L MH, 374D L
5N3764 COUPLING GP-FLEXIBLE
3508, 3512, 3516, D398, D398B, D399
1470082 COUPLING AS-FLEXIBLE
3606, 3608, 3612, 3616, G3606, G3608, G3612, G3616
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.