1301251 COVER Caterpillar parts
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 836G, 836H, 950G, 962G, 980G, 980G II, 980H
Rating:
Alternative (cross code) number:
CA1301251
130-1251
1301251
CA1301251
130-1251
1301251
Weight: 6 pounds 2 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 1301251:
Information:
Removal Procedure
Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".Note: Before you begin the following procedure, swing the upper structure in order to gain access to the plate assembly which is located under the rear of the cab.Note: Put identification marks on all hose assemblies, fittings and ports so that all the components can be reassembled in the original configuration. Plug all of the hose assemblies and cap all of the fittings. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Open the right rear access door.
Illustration 1 g01154764
Remove hydraulic accumulator (1) .Installation Procedure
Illustration 2 g01154764
Install hydraulic accumulator (1) .
Close the right rear access door.
Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".Note: Before you begin the following procedure, swing the upper structure in order to gain access to the plate assembly which is located under the rear of the cab.Note: Put identification marks on all hose assemblies, fittings and ports so that all the components can be reassembled in the original configuration. Plug all of the hose assemblies and cap all of the fittings. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Open the right rear access door.
Illustration 1 g01154764
Remove hydraulic accumulator (1) .Installation Procedure
Illustration 2 g01154764
Install hydraulic accumulator (1) .
Close the right rear access door.
Caterpillar parts catalog:
Parts cover Caterpillar catalog:
1722142
COVER
980G
980G
1W3861
COVER-ADVANCE
824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G
824C, 824G, 825G, 826C, 826G, 980C, 980F, 980G
2Q7739
COVER AS-LH
980G, 980G II
980G, 980G II
2Q7738
COVER AS-RH
980G
980G
4E0538
COVER AS-LH
950F, 950F II, 950G, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G
950F, 950F II, 950G, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G
1902258
COVER
980G
980G
1894242
COVER GP
980G
980G
1892038
COVER GP
980G
980G
1890635
COVER GP
980G
980G
1558751
COVER
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 980H
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 980H
1156901
COVER
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H
824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 972G, 972G II, 972H, 980G, 980G II, 980H