AVSPARE.COM
parts catalog

COVER 1400076 - Caterpillar



1400076 COVER Caterpillar parts 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G COVER
Rating:
9
Alternative (cross code) number:
CA1400076
140-0076
1400076
Caterpillar 1400076 COVER
Weight: 1 pounds 0 kg.

Buy COVER 1400076 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 1400076:

INTEGRATED TOOLCARRIER  IT62G  
LANDFILL COMPACTOR  826G  
SOIL COMPACTOR  825G  
WHEEL LOADER  950G   962G   966G   972G   980G   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:


Table 1
914G and 914G2 Wheel Loader Cycle Times    
Machine Function     Time in Seconds    
Lift with empty bucket (1)     5.2 0.7    
Dump with empty bucket (2)     2.0 0.4    
( 1 ) The work tool is in the full TILT position.
( 2 ) The lift arms are in the full RAISE position.
Table 2
IT14G and IT14G2 Integrated Toolcarrier Cycle Times    
Machine Function     Time in Seconds    
Lift with empty bucket (1)     6.1 0.7    
Dump with empty bucket (2)     3.0 0.4    
( 1 ) The work tool is in the full TILT position.
( 2 ) The lift arms are in the full RAISE position.The speed of the implements is affected by the amount of oil flow that is produced by the implement pump. Check the implement cycle times in order to determine if there may be a problem with the implement pump.
Perform the machine preparation for testing.ReferenceFor more information about preparing the machine for troubleshooting, refer to the Service Manual module Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.
Illustration 1 g00934339
Warm the hydraulic oil to normal operating temperature. Normal operating temperature that is needed in order to run the cycle time test is between 38 °C (100 °F) and 65 °C (150 °F). If Caterpillar Electronic Technician is being used, the hydraulic oil temperature can be monitored on the screen. Refer to Illustration 1, for the location on the screen for the hydraulic oil temperature.
Place the ride control switch in the OFF position.
Begin the test for the lift cycle time with the work tool in the full TILT position.
Increase the engine speed to high idle.
Pull the lift control lever back to the full RAISE position. Measure the cycle time from the work tool flat on the ground to the full RAISE position. Record the lift cycle time.
Ensure that the lift linkage in the full RAISE position and the work tool is in the full TILT position.
Move the tilt control lever to the full DUMP position. Measure the time for the work tool to travel from the full TILT position to the full DUMP position. Record the cycle time for dump.
Reduce engine speed to low idle.
Lower the work tool to the ground.
Turn the engine start switch to the OFF position.Compare the test results with the cycle times that are listed in Table 1 for the 914G and 914G2 Wheel Loader. Compare the test results with the cycle times that are listed in Table 2 for the IT14G and IT14G2 Integrated Toolcarrier. The implement pump should be working properly if the implement cycle times match the cycle times that are listed in Tables.If, the cycle times are not correct for both the lift and tilt functions one of the following conditions are probably present:
The pump may have excessive wear.If, the cycle time is slow for only one of the implement circuits, see the following conditions. The circuit with slow

Caterpillar parts catalog:

Caterpillar parts catalog
825G Soil Compactor 6RN00001-UP (MACHINE) POWERED BY 3406 Engine
826G Landfill Compactor 7LN00001-UP (MACHINE) POWERED BY 3406 Engine
IT62G Integrated Toolcarrier 6PS00001-UP (MACHINE) POWERED BY 3126 Engine
IT62G Integrated Tool Carrier AKP00001-UP (MACHINE) POWERED BY 3126 Engine
4Q-1795 Conversion Ar-Underground Mine Custom Product Support Literature for 980G Wheel Loader 9CM00001-UP (MACHINE)
980G Wheel Loader 2KR00001-UP (MACHINE) POWERED BY 3406C Engine
980G Wheel Loader 9CM00001-UP (MACHINE) POWERED BY 3406C Engine
950G Wheel Loader 4BS00001-UP (MACHINE) POWERED BY 3126 Engine
962G Wheel Loader 5AS00001-UP (MACHINE) POWERED BY 3126 Engine
950G Wheel Loader 2JS00001-UP (MACHINE) POWERED BY 3126 Engine
962G Wheel Loader 3BS00001-UP (MACHINE) POWERED BY 3126 Engine
966G Wheel Loader 3ZS00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine
966G Wheel Loader 9RS00001-UP (MACHINE) POWERED BY 3306 Engine
950G Wheel Loader 8JW00001-UP (MACHINE) POWERED BY 3126 Engine
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
950G Wheel Loader 3JW00001-UP (MACHINE) POWERED BY 3126 Engine
962G Wheel Loader 4PW00001-UP (MACHINE) POWERED BY 3126 Engine
966G Wheel Loader 3SW00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine
950G Wheel Loader 5FW00001-UP (MACHINE) POWERED BY 3126 Engine
962G Wheel Loader 7BW00001-UP (MACHINE) POWERED BY 3126 Engine
966G Wheel Loader 3PW00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 6AW00001-UP (MACHINE) POWERED BY 3306 Engine


Parts cover Caterpillar catalog:

1765500 COVER AS
824G, 824G II, 825G, 826G, 826G II, 950G, 962G, 966G, 972G, 980G, IT62G
1144208 COVER AS
69D, 769D, 771D, 773D, 773E, 775D, 775E, 776D, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 797, 797B, 824G, 824G II, 825G, 826G, 826G II, 950G, 962G, 966G, 972G, 980G, IT62G
1432240 COVER AS
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
1703450 COVER AS
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, IT62G, IT62G II
1418811 COVER AS
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 986H, 988H, IT62G, IT62G II, IT62H
1418808 COVER AS
950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II, 966H, 972G, 972G II, 972H, 986H, 988H, IT62G, IT62G II, IT62H
1497682 COVER
950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, IT62G, IT62G II
1646318 COVER
824G, 824G II, 824H, 825G, 825G II, 825H, 950G, 962G, 966G, 972G, 980G, IT62G
1150235 COVER
824G, 824G II, 824H, 825G, 825G II, 825H, 950G, 962G, 966G, 972G, 980G, IT62G
2027652 COVER AS
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 834G, 834H, 836G, 836H, 950G, 962G, 966G, 972G, 980G, 988G, 988H, IT62G
1400080 COVER
825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
1400078 COVER
825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.