2271023 COVER Caterpillar parts
315C, 317B LN, 318B, 933C, 939C
Rating:
Alternative (cross code) number:
CA2271023
227-1023
2271023
CA2271023
227-1023
2271023
Weight: 1 pounds 0 kg.
EXCAVATOR, TRACK LOADER,
Compatible equipment models: 2271023:
Number on catalog scheme:
7
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize Lubricant -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g03389516
Remove temperature sensor (3). Disconnect tube assembly (4). Loosen clamp (1) and disconnect strap (2).
Illustration 2 g03389543
Disconnect band clamp (6) and remove inlet module (catalyst) (5). Installation Procedure
Note: When installing a new inlet module (catalyst) or a cleaned inlet module (catalyst), a DOC reset must be performed. Refer to Special Instruction, REHS8180, "Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC), and a Selective Catalyst Reduction (SCR) Filter" for the correct procedure.
Install inlet module (catalyst) (5) in the reverse order of removal.
Illustration 3 g03389555
Facing the Inlet Module Assembly.
Install clamp (1) to Dimension (Y). Dimension (Y) is 30° 5°. Tighten clamp (1) to a torque of 60 5 N m (44 4 lb ft).
Illustration 4 g03381770
Typical Example
Note: Do not use power tools in order to torque strap (2).
Apply Tooling (A) to the threads of strap (2) along Distance (Z). Distance (Z) is 25 mm (1.0 inch) above the trunnion. Tighten strap (2) to a torque of 15 + 3 - 0 N m (133 + 27 - 0 lb in).
Illustration 5 g03381887
Cutaway view of band clamp (6) in position on the assembly.
Note: Do not use power tools in order to torque band clamp (6).
Verify that the cup of the Ball Joint (G) does not touch the radius of the Ball (F). Position band clamp (6) and hand tighten band clamp (6). Band clamp (6) should be in the center of the joint.
Dimension (D) and Dimension (E) should be equal within 2.0 mm (0.08 inch). Repeat the measurements every 90° around band clamp (6). If necessary, adjust band clamp (6).
Torque band clamp (6) to a torque of 35 2 N m (26 1 lb ft).
Apply Tooling (A) to the threads of temperature sensor (3). Tighten temperature sensor (3) to a torque of 45 5 N m (33 4 lb ft).
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite Nickel Anti-Seize Lubricant -
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Illustration 1 g03389516
Remove temperature sensor (3). Disconnect tube assembly (4). Loosen clamp (1) and disconnect strap (2).
Illustration 2 g03389543
Disconnect band clamp (6) and remove inlet module (catalyst) (5). Installation Procedure
Note: When installing a new inlet module (catalyst) or a cleaned inlet module (catalyst), a DOC reset must be performed. Refer to Special Instruction, REHS8180, "Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC), and a Selective Catalyst Reduction (SCR) Filter" for the correct procedure.
Install inlet module (catalyst) (5) in the reverse order of removal.
Illustration 3 g03389555
Facing the Inlet Module Assembly.
Install clamp (1) to Dimension (Y). Dimension (Y) is 30° 5°. Tighten clamp (1) to a torque of 60 5 N m (44 4 lb ft).
Illustration 4 g03381770
Typical Example
Note: Do not use power tools in order to torque strap (2).
Apply Tooling (A) to the threads of strap (2) along Distance (Z). Distance (Z) is 25 mm (1.0 inch) above the trunnion. Tighten strap (2) to a torque of 15 + 3 - 0 N m (133 + 27 - 0 lb in).
Illustration 5 g03381887
Cutaway view of band clamp (6) in position on the assembly.
Note: Do not use power tools in order to torque band clamp (6).
Verify that the cup of the Ball Joint (G) does not touch the radius of the Ball (F). Position band clamp (6) and hand tighten band clamp (6). Band clamp (6) should be in the center of the joint.
Dimension (D) and Dimension (E) should be equal within 2.0 mm (0.08 inch). Repeat the measurements every 90° around band clamp (6). If necessary, adjust band clamp (6).
Torque band clamp (6) to a torque of 35 2 N m (26 1 lb ft).
Apply Tooling (A) to the threads of temperature sensor (3). Tighten temperature sensor (3) to a torque of 45 5 N m (33 4 lb ft).
Caterpillar parts catalog:
Parts cover Caterpillar catalog:
1961421
COVER GP-ACCESS
312C, 312C L, 315C, 318C, 320C, 320C FM, 320C L, 322C, 325C, 330C, 330C L
312C, 312C L, 315C, 318C, 320C, 320C FM, 320C L, 322C, 325C, 330C, 330C L
216, 228, 236, 236B, 236B3, 242B3, 246C, 247, 248, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 3054...
120G, 120H, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12K, 12M, 130G, 135H, 1390, 140G, 140H, 140K, 140K 2, 143H, 14H, 160G, 160H, 160K, 163H, 16H, 215, 215B, 2384C, 2484C, 24H, 24M, 2590, 30/30, 305.5, 3...
1090, 1190, 1190T, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H,...
416B, 426B, 428, 428B, 933, 933C, CS-323C, D3C III, D3G, D4C III, D4G
120B, 12F, 16, 215, 215B, 225, 3114, 3116, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312E, 312E L, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 3208, 3304, 416B, 428B, 438B, 446B, 446D, ...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906, 906H, 907H, 908, 908H, 933, 933C, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ES, 160H NA, 16...
311, 311B, 311C, 312, 312B, 315, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L...
311, 311B, 312, 312B, 313D2 LGP, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C L, ...
5I8799
COVER
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E HVG, 336E L, 336E LN, 340D L,...
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E HVG, 336E L, 336E LN, 340D L,...
315C, 315D L, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 3...
1697978
COVER
311B, 312B, 317B LN, 318B
311B, 312B, 317B LN, 318B
1515295
COVER AS-VALVE
315B, 315C, 317B LN, 318B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
315B, 315C, 317B LN, 318B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
1609173
COVER
315B L, OEMS
315B L, OEMS
1609172
COVER
315B L, OEMS
315B L, OEMS
315B L, 317B LN, 318B
1351384
COVER AS-FUEL TANK
315B, 315B FM L, 315B L, 317B LN, 318B
315B, 315B FM L, 315B L, 317B LN, 318B
1184799
COVER AS
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
307, 315, 315B, 315C, 317B LN, 318B, 933, 933C, D3C III, D4C III
1275925
COVER-TURBOCHARGER
315, 315B, 315C, 317B LN, 318B
315, 315B, 315C, 317B LN, 318B
1355784
COVER AS
315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319D L, 319D LN
315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319D L, 319D LN
0953569
COVER-THERMOSTAT
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1593126
COVER
315B, 315C, 317B LN, 318B
315B, 315C, 317B LN, 318B