COVER AS-RH 2468366 - Caterpillar

Install bracket assembly (41) using retained hardware. Repeat the step for the opposite side of the machine with bracket assembly (42).
Illustration 26 g03342642
A view of the lower updated air lines group
(C) 329-3555 Half Clip
(17) 5P-1076 Hard Washers
(39) 366-8500 Hoses
(40) 135-6261 Clamps
(43) 391-7193 Tubes
(44) 8T-4194 Bolts
(45) 8T-4244 Nuts
(46) 282-6679 Clamps
(47) 419-6027 Plates
Install two tubes (43) on the underside of the aftercooler with two hoses (39) and eight clamps (40). Secure the tubes (43) with half clips (C) with two bolts (44), four hard washers (17), and two nuts (45).Note: Install clamps (40) at 180 degree angles so that the clamps face opposite directions.
Also secure tubes (43) with four clamps (46). Secure clamps (46) with six bolts (44), 12 hard washers (17), and six nuts (45). Connect clamps (46) with two plates (47). Leave all hardware loose until all hardware in this step is assembled, then tighten.Note: Install clamps (40) at 180 degree angles so that the clamps face opposite directions.
Illustration 27 g03342784
A view of the lower updated air lines group
(39) 366-8500 Hoses
(40) 135-6261 Clamps
(43) 391-7193 Tubes
(48) 391-7194 Tube
(49) 391-7195 Tube
Install tubes (48) and (49). Attach the tubes (48) and (49) to tubes (43) with two hoses (37). Secure hoses (39) with eight clamps (40).
Illustration 28 g03342850
A view of the lower updated air lines group
(C) 329-3555 Half Clip
(17) 5P-1076 Hard Washers
(25) 8T-4183 Bolts
(27) 374-9479 Stabilizer
(48) 391-7194 Tube
(49) 391-7195 Tube
Secure tubes (48) and (49) with six half clips (C) each. Secure the clips with two bolts (25) and hard washers (17) per pair of half clips.
Illustration 29 g03343727
A view of the lower updated air lines group
(40) 135-6261 Clamps
(48) 391-7194 Tube
(49) 391-7195 Tube
(50) 294-7373 Hoses
Connect tubes (48) and (49) to the existing air lines with two hoses (50) and eight clamps (40).
Illustration 30 g03343059
A view of the upper updated air lines group
(A) 367-4960 Tube As
(B) 367-4959 Tube As
(C) 329-3555 Half Clip
Install tube assembly (A) and (B). Reuse half clips (C) and hardware retained from Step 2.
Illustration 31 g03343109
A view of the upper updated air lines group
(A) 367-4960 Tube As
(B) 367-4959 Tube As
(37) 374-8510 Tube
(39) 366-8500 Hoses
(40) 135-6261 Clamps
Secure tube assemblies (A) and (B) to two tubes (37) with hoses (39). Secure hoses (39) with eight clamps (40).
Illustration 32 g03351418
A view of the updated lower air lines group
(51) 5M-6214 Pipe Plug
Install pipe plug (51) in the air lines group. Refer to Illustration 32.
Using a suitable lifting device, install the radiator module in the machine. Refer to Disassembly and Assembly, KENR8726, "Radiator Module - Install".