COVER AS-FILTER 2941770 - Caterpillar

Position plate (1) on the plate assembly for the body.Note: Measurement (A) is a 10 1 Degree angle measured counter clockwise from a line that goes through the pivot bore and is parallel with the ground.Note: Measurement (B) locates the top of plate (1) .Note: Measurement (C) is a 10 1 Degree angle measured counter clockwise from a line that goes through the center of the pivot bore and is perpendicular to the ground.Note: Measurement (D) locates the back edge of plate (1) .
Tack weld plate (1) in place.Note: Refer to Special Instruction, REHS1841, "General Welding Procedures" before performing any welding on the machine.
Illustration 9 g02830317
(1) Plate (2) 5G-7820 Magnet As (3) 8T-7547 Bolt (4) 8T-4224 Hard Washer (5) 6V-9189 Locknut
Secure magnet assembly (2) to plate (1) by using two bolts (3), four hard washers (4), and two locknuts (5) .Note: Leave magnet assembly (2) loose for adjustment.
Illustration 10 g02836979
View of the rear of the frame (D) Block (6) 384-4121 Plate (7) 8T-4137 Bolt (8) 8T-4121 Hard Washer
Secure plate (6) to block (D) by using two bolts (7), and two hard washers (8) .Note: Tighten bolts (7) to a torque of 55 10 N m (40.5 7.4 lb ft).
Illustration 11 g02836996
View of the rear of the frame (4) 8T-4224 Hard Washer (6) 384-4121 Plate (9) 130-5300 Clip (10) 228-4808 Position Switch Gp (11) 4M-6425 Bolt
Secure one position switch group (10) and one clip (9) to plate (6) by using two bolts (11) and two hard washers (4) .Note: Tighten bolts (11) to a torque of 25 6 N m (220 55 lb in).
Illustration 12 g02839519
(E) Chassis harness assembly (F) Boss (8) 8T-4121 Hard Washer (9) 130-5300 Clip (10) 228-4808 Position Switch Gp (12) 383-2704 Switch Harness As (13) 7K-1181 Cable Strap (14) 132-5789 Clip (15) 132-7551 Spacer (16) 8T-4136 Bolt
Connect switch harness assembly (12) to position switch group (10) and chassis harness assembly (E) .
Secure harness assembly (12) and chassis harness assembly (E) to boss (F) using spacer (15), clip (9), clip (14), hard washer (8), bolt (16), and cable strap (13) .
Remove the body retaining pin and operate the hoist of the truck. Note: Refer to Operation and Maintenance Manual, SEBU7837 for instructions on removing the pins and operating the hoist.
Illustration 13 g02840165
(E) Chassis harness assembly (G) 10 mm (0.394 inch) (2) 5G-7820 Magnet As (6) 384-4121 Plate (10) 228-4808 Position Switch Gp
With the body in the DOWN position, adjust magnet assembly (2) and position switch group (10) so that dimension (G) is 10 mm (0.394 inch).Note: Adjust plate (6) forward or backwards in order to achieve dimension 10 mm (0.394 inch).
Position magnet assembly (2) so that the body snubs at 203 to 254 mm (8 to 10 inch) between the front body pads and