AVSPARE.COM
parts catalog

COVER AS 3727641 - Caterpillar



3727641 COVER AS Caterpillar parts COVER
Rating:
66
Alternative (cross code) number:
CA3727641
372-7641
3727641
Caterpillar 3727641 COVER AS

Buy COVER AS 3727641 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 2 g03245478
Right side view
Table 2
Item Qty Part Specification Description
The camshaft bearings (2) are installed into the cylinder block at the following positions:
- - - Distance (F) is 1120.0 1.5 mm (44.09 0.06 inch).
- - - Distance (G) is 850.0 1.5 mm (33.46 0.06 inch).
- - - Distance (H) is 580.0 1.5 mm (22.83 0.06 inch).
- - - Distance (J) is 310.0 1.5 mm (12.20 0.06 inch).
- - - Distance (K) is 40.0 0.5 mm (1.57 0.02 inch).
4 3 7N-2047 Dowel Extension (L) of the dowel is 6.0 0.5 mm (0.24 0.02 inch).
5 2 8T-2929 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
6 2 8T-2928 O-Ring Seal Before assembly, lubricate the bore lightly with the lubricant that is being sealed.
7 2 4N-0683 Dowel Extension (M) of the dowel is 19.0 0.5 mm (0.75 0.012 inch).
8 2 7N-2044 Dowel Extension (N) of the dowel is 40.0 0.5 mm (1.57 0.02 inch).
Illustration 3 g03245479
Front view
Table 3
Item Qty Part Specification Description
R - - New dimension from centerline of crankshaft bearing bore to the top of the cylinder block is 586 mm (23.1 inch).
9 8 352-6061 Liner Seal Assemble liner seals dry on clean and dry liner grooves.
Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.
10 24 7N-2046 O-Ring Seal Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap.
11 5 223-1696 Crankshaft Bearing Cap Width of the crankshaft bearing cap is 340.030 0.015 mm (13.3870 0.0006 inch).
Width (P) in the cylinder block for crankshaft bearing cap is 339.985 0.015 mm (13.3852 0.0006 inch).
12 20 7X-7925 Bolt Use the following procedure in order to tighten the crankshaft bearing cap bolts:
Install main bearing caps with the cast part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail.
1. Before assembly, lubricate the threads completely with clean engine oil.
2. Hand tighten bolts in the tapped holes.
3. Tighten bolts in the numerical sequence as shown in Illustration 3 to 190 14 N m (140 10 lb ft).
4. Again, tighten each bolt to an additional angle of 180 5 degrees.


Parts cover Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.