AVSPARE.COM
parts catalog

COVER AS 3727658 - Caterpillar



3727658 COVER AS Caterpillar parts COVER
Rating:
11
Alternative (cross code) number:
CA3727658
372-7658
3727658
Caterpillar 3727658 COVER AS

Buy COVER AS 3727658 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 4 g01360095
Terminal locations at the engine interface connector that are associated with the CAN data link
(P1-16) CAN shield
(P1-17) CAN data link +
(P1-18) CAN data link −
Illustration 5 g01209794
Terminal locations at the service tool connector that are associated with the CAN data link
(Terminal C) CAN shield
(Terminal F) CAN data link −
(Terminal G) CAN data link +
Illustration 6 g01355248
Terminal locations at the service tool connector that are associated with the CAN data link
(Terminal C) CAN shield
(Terminal F) CAN data link −
(Terminal G) CAN data link +
Table 1
Troubleshooting Test Step Values Results
1. Inspect the Electrical Connectors and the Wiring
A. Remove the electrical power from the ECM.
B. Thoroughly inspect connectors (1), (2), and (3). Inspect all of the connectors that are associated with the CAN data link. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
D. Check the allen head screw on each ECM connector and on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the wiring harnesses for abrasion, for corrosion and for pinch points.
All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.
Result: The harness and wiring appear to be OK. Proceed to Test Step 2.
Result: There is a problem in the wiring harness.
Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.
2. Verify the Proper Installation of the Termination Resistors
A. Remove the electrical power from the ECM.
B. Disconnect the display panel from the data link.
C. Disconnect the Caterpillar Electronic Technician (ET) from the service tool connector.
D. Disconnect the P1 ECM connector.
Wiggle the harness during the following measurements in order to reveal an intermittent condition.
E. Measure the resistance between terminals P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -).
The resistance is between 57 and 63 Ohms.
Result: The resistance is between 57 and 63 Ohms. Proceed to Test Step 3.
Result: The resistance is between 114 Ohms and 126 Ohms. A termination resistor is missing
Verify that two termination resistors are connected to the data link. One resistor must be located on each end of the data link. The engine is shipped with one termination resistor that is installed between the ECM and the customer connector.
Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.
The resistance is less than 57 Ohms. There may be a short circuit in the harness. Proceed to Test Step 3.
The resistance is greater than 126 Ohms. There may be an open circuit in the harness. Proceed to Test Step 4.
Table 2
Resistance Measurements for the CAN Data Link
Connector and Terminal Terminal
P1-50


Parts cover Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.