AVSPARE.COM
parts catalog

COVER 4416010 - Caterpillar



4416010 COVER Caterpillar parts SAT318T COVER
Rating:
78
Alternative (cross code) number:
CA4416010
441-6010
4416010
Caterpillar 4416010 COVER

Buy COVER 4416010 Caterpillar genuine, new aftermarket tractor parts with delivery
HARVESTER HEAD,

Compatible equipment models: 4416010:

HARVESTER HEAD  SAT318T   Caterpillar
  For full view, you need register

Information:


TECHNICAL INFORMATION BULLETIN October 24, 2001
Engines
Generator Sets 3508 (23Z, 69Z, 70Z, 96Y, 3LS,
5XM)
3508B (6PN, 4GM, 2HW)
3512 (24Z, 66Z, 67Z, 6PM, 3MS,
50Y)
3512B (8RM, 6WN, 5AW, 4AW)
3516 (29Z, 25Z, 72Z, 73Z, 4XF
5SJ, 4MJ, 7KM, 3NS)
3516B (7RN, 6HN, 2JW, 1NW)
G3508 (2JF, 4WD, 9TG, 2TJ)
G3512 (4KC, 5JD, 7NJ)
G3516 (3RC, 8LD, 4EK)
3516 (8TW)
3516B (8NW)
G3508 (CPJ, CPS)
G3512 (CSP, CRN)
G3516 (CPG, CSZ)
` Component Code(s) 1409SUBJECT: Power Transformer (PT) Failures Due to Overburden of the Medium Voltage Power Transformers
PROBLEM: The 149-3403 Transformer is a medium voltage power transformer that is rated at 5 VA maximum output. On a 149-3403 Transformer with 240 volt load-share module sensing, the load puts a total burden of approximately 6.47 VA on phase two of the three-phase transformer configuration. This can lead to early failure of the solder connection and can cause corona damage inside the generator cabinet.
SOLUTION: Using the 35:1 PT secondary leads instead of the 17.5:1 leads, rewire the load-share-sensing voltage to the 120 VAC input. At 120 VAC sensing, the VA rating of the Woodward load-share-sensing circuit drops to approximately 2.35 VA per phase.
Perform the following steps in order to reduce the load on the transformers and to provide long-term reliable operation.
Remove the load share sensing leads from terminals 20, 22, and 24. Re-attach these leads to terminals T1, T3, and T2 on the 170-5400 Terminal Strip Group. Refer to Illustration 1, Illustration 2, and Illustration 3.
Locate the leads of the TX1 secondary output and the TX2 secondary output. The leads of the TX1 secondary output and the TX2 secondary output are black with white tracers. These leads should be connected to terminal T1 and terminal T3 on the 170-5400 Terminal Strip Group.
Install a 14 gauge jumper wire from terminal 24 (170-5400 Terminal Strip Group) to terminal T2 (170-5400 Terminal Strip Group). This will bring the total burden on the potential transformers to approximately 4 VA.
If main the Terminal Strip does not have T2, refer to Illustration 3 in order to connect the Load Share Module.
Note: When medium voltage generator transformer sensing leads are attached to the bus bars, apply an equal amount of torque to connections T1, T2, T3, and T0. If equal torque is not applied to these connections, voltage losses across the poor connections could cause voltage readout accuracy errors on the EMCPII.
During operation, there should be approximately 120 ACV across any two of the following 170-5400 Terminal Strip terminals: T1, T2, and T3. Refer to Table 1.
Table 1
170-5400 Terminal Strip Voltages
Terminals Measured Voltage Across Terminals
T1 and T2 120 ACV
T1 and T3 120 ACV
T2 and T3 120 ACV
Illustration 1. Old 240 volt wiring
Illustration 2. New 120 Volt Wiring
Illustration 3. New 120 volt wiring
COPYRIGHT 2001 CATERPILLAR
ALL RIGHTS RESERVED


Parts cover Caterpillar catalog:

4501168 COVER
SAT22DB, SAT322
4501167 COVER
SAT22DB, SAT322
4501166 COVER AS
SAT22DB, SAT322
4416026 COVER
SAT318T, SAT322
4521362 COVER
SAT318T, SAT322
4416014 COVER
SAT318T, SAT322
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.