5403135 COVER Caterpillar parts
Rating:
Alternative (cross code) number:
CA5403135
540-3135
5403135
CA5403135
540-3135
5403135
Number on catalog scheme:
60
For full view, you need register
Caterpillar parts catalog:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g02717775
If necessary, install the cover to the water pump . Follow Steps 2.a through 2.d in order to install the cover.
Clean the gasket surface of cover (7).
Position a new gasket (6) (not shown) on water pump (3).
Install cover (7) to water pump (3).
Install bolts (9) to cover (7). Tighten bolts finger tight.
Illustration 2 g02721481
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Illustration 3 g02721493
Bolts (9) for cover plate.
(5) M8 by 30 mm
(4) M8 by 75 mm
(8) M8 by 65 mm
Illustration 4 g02721495
Install bolts (4), bolts (5), and bolts (8). Refer to Illustration 3. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Tighten bolts (4), bolts (5), bolts (8), and bolts (9) in the sequence that is shown in Illustration 4 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
(M8 by 70 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear or damage. If necessary, replace the water pump.
Illustration 1 g02717775
If necessary, install the cover to the water pump . Follow Steps 2.a through 2.d in order to install the cover.
Clean the gasket surface of cover (7).
Position a new gasket (6) (not shown) on water pump (3).
Install cover (7) to water pump (3).
Install bolts (9) to cover (7). Tighten bolts finger tight.
Illustration 2 g02721481
Clean the gasket surface of front cover (1).
Install Tooling (A) in Position (X).
Use Tooling (A) in order to align new gasket (2) to front cover (1). Install the gasket to the front cover.
Align water pump (3) to Tooling (A). Install the water pump to front cover (1). Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Illustration 3 g02721493
Bolts (9) for cover plate.
(5) M8 by 30 mm
(4) M8 by 75 mm
(8) M8 by 65 mm
Illustration 4 g02721495
Install bolts (4), bolts (5), and bolts (8). Refer to Illustration 3. Tighten the bolts finger tight. Note: Ensure that all bolts of different lengths are installed in the correct positions.
Remove Tooling (A) and install remaining bolts (4).
Tighten bolts (4), bolts (5), bolts (8), and bolts (9) in the sequence that is shown in Illustration 4 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure. End By:
Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Parts cover Caterpillar catalog:
5400083
COVER
Caterpillar
Caterpillar
5400072
COVER
Caterpillar
Caterpillar
5399109
COVER-DASH
Caterpillar
Caterpillar
5398579
COVER AS
Caterpillar
Caterpillar
5398577
COVER AS-ACCESS
Caterpillar
Caterpillar
5394448
COVER
Caterpillar
Caterpillar
5458567
COVER
Caterpillar
Caterpillar
5432116
COVER
Caterpillar
Caterpillar
5426455
COVER AS
Caterpillar
Caterpillar
5416950
COVER
Caterpillar
Caterpillar
5410089
COVER AS
Caterpillar
Caterpillar
5407039
COVER AS-VALVE
Caterpillar
Caterpillar