6E4227 COVER Caterpillar parts
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 24H, 24M, 5230, 5230B, 789B, 789C, 789D, 793, 793B, 793C, D8N, D8R, D8R II, D9R
Rating:
Alternative (cross code) number:
CA6E4227
6E-4227
6E4227
CA6E4227
6E-4227
6E4227
Weight: 2 pounds 1 kg.
MINING EXCAVATOR, TRUCK,
Compatible equipment models: 6E4227:
Information:
All Industrial, Marine, Generator Set, and Truck EnginesThis article gives the procedures used at Caterpillar to make engine fuel settings and the procedure that must be used in the field. It also tells why there can be differences between the fuel setting dimension on the fuel setting microfiche, the dimension on the engine information plate and the actual setting.
ALL ENGINES EXCEPT 3500 SERIES ENGINES
Before a new engine arrangement is built, design specifications and engine tests are used to find the correct fuel setting for that engine rating. Over a period of time as engines are built, components will change a small amount. Because of these changes the fuel setting specification must be changed to keep the average engine power as close as possible to the rating. The new fuel setting specification is then stamped on the engine information plate. The fuel setting microfiche has fuel setting dimensions for all the engines, but the dimension on the microfiche may not be exactly the same as the one on the engine information plate. The microfiche is changed only when the specification has changed more than 0.25 mm (.010") from what the setting was before. The dimensions in the microfiche can be used for engines which are to be set for a rating which is different from the rating set at the factory.
The dimension on the engine information plate is the most accurate and must be used as long as the engine is still in its original factory configuration.A new fuel setting "checking" tolerance must now be used on all engines. The new "checking" tolerances is 0.25 mm (.010") is only for when a fuel setting is checked. If the fuel setting is within the "checking" tolerance it must not be changed. The "checking" tolerance is not to be used to adjust the fuel setting. If the fuel setting dimension is outside the tolerance, it must be set to the dimensions on the engine information plate. 0.13 mm (.005") of the "checking" tolerance is necessary because it is possible for different servicemen with different sets of tools, to get different results. The other 0.13 mm (.005") is because of tolerances and changes at the factory.
When an engine is tested on a dynamometer and has correct Brake Specific Fuel Consumption (BSFC), it is permissible to adjust to a setting that is 0.25 mm (.010") different than the dimension specified on the engine information plate to get correct fuel rate and 3% of the rated power. However, if the setting from the dynamometer test is not within 0.25 mm (.010") of the information plate setting, it is recommended that the engine be thoroughly checked to make sure assembly or adjustment is correct. Remember, when a recheck of this by a different serviceman is made, the dimension can be as much as 0.28 mm (.015") different from the dimension on the plate.
3500 Series Engines
The different fuel system design of the 3500 Series Engine use the same procedure as the other
ALL ENGINES EXCEPT 3500 SERIES ENGINES
Before a new engine arrangement is built, design specifications and engine tests are used to find the correct fuel setting for that engine rating. Over a period of time as engines are built, components will change a small amount. Because of these changes the fuel setting specification must be changed to keep the average engine power as close as possible to the rating. The new fuel setting specification is then stamped on the engine information plate. The fuel setting microfiche has fuel setting dimensions for all the engines, but the dimension on the microfiche may not be exactly the same as the one on the engine information plate. The microfiche is changed only when the specification has changed more than 0.25 mm (.010") from what the setting was before. The dimensions in the microfiche can be used for engines which are to be set for a rating which is different from the rating set at the factory.
The dimension on the engine information plate is the most accurate and must be used as long as the engine is still in its original factory configuration.A new fuel setting "checking" tolerance must now be used on all engines. The new "checking" tolerances is 0.25 mm (.010") is only for when a fuel setting is checked. If the fuel setting is within the "checking" tolerance it must not be changed. The "checking" tolerance is not to be used to adjust the fuel setting. If the fuel setting dimension is outside the tolerance, it must be set to the dimensions on the engine information plate. 0.13 mm (.005") of the "checking" tolerance is necessary because it is possible for different servicemen with different sets of tools, to get different results. The other 0.13 mm (.005") is because of tolerances and changes at the factory.
When an engine is tested on a dynamometer and has correct Brake Specific Fuel Consumption (BSFC), it is permissible to adjust to a setting that is 0.25 mm (.010") different than the dimension specified on the engine information plate to get correct fuel rate and 3% of the rated power. However, if the setting from the dynamometer test is not within 0.25 mm (.010") of the information plate setting, it is recommended that the engine be thoroughly checked to make sure assembly or adjustment is correct. Remember, when a recheck of this by a different serviceman is made, the dimension can be as much as 0.28 mm (.015") different from the dimension on the plate.
3500 Series Engines
The different fuel system design of the 3500 Series Engine use the same procedure as the other
Cat SIS web machinery list:
Parts cover Caterpillar catalog:
3S3439
COVER-TOP
572G, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637E, 637G, 735, 740, 776, 776C, 776D, 777, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 789B, 7...
572G, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637E, 637G, 735, 740, 776, 776C, 776D, 777, 777B, 777D, 777F, 777G, 784B, 784C, 785, 785B, 785C, 785D, 789B, 7...
9P3474
COVER
589, D8L, D9N, D9R, D9T
589, D8L, D9N, D9R, D9T
6P8931
COVER
578, 583R, 583T, 587R, 587T, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T, PL83, PL87
578, 583R, 583T, 587R, 587T, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T, PL83, PL87
2P2508
COVER AS-PRECLEANER
24H, 583T, 587T, 854K, 992, 992K, 993K, D10N, D10R, D10T, D11R, D11T, D8R, D8T, D9L, PL83, PL87
24H, 583T, 587T, 854K, 992, 992K, 993K, D10N, D10R, D10T, D11R, D11T, D8R, D8T, D9L, PL83, PL87
9P7823
COVER
D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
1119862
COVER-STARTING MOTOR
5130B, 836, 966F II, 980G, D10R, D11R, D7R II, D8R, D8R II, D9R
5130B, 836, 966F II, 980G, D10R, D11R, D7R II, D8R, D8R II, D9R
3G2665
COVER
5130, 5130B, 5230, 5230B, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R29...
5130, 5130B, 5230, 5230B, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R29...
2P1014
COVER AS-PUMP
24H, 824B, 834B, 836, 980C, 980F, 980F II, 988B, 988F, 988F II, AD40, AE40, D10N, D10R, D8L, D9L, D9R, R1700 II, R1700G
24H, 824B, 834B, 836, 980C, 980F, 980F II, 988B, 988F, 988F II, AD40, AE40, D10N, D10R, D8L, D9L, D9R, R1700 II, R1700G
7D5435
COVER
24H, 24M, 770, 770G, 770G OEM, 772, 772B, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776C, 776D, 777, 777B, 777D, 777F, 77...
24H, 24M, 770, 770G, 770G OEM, 772, 772B, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 776C, 776D, 777, 777B, 777D, 777F, 77...
9W5575
COVER AS
D10N, D10R, D10T, D9L, D9N, D9R
D10N, D10R, D10T, D9L, D9N, D9R
6G0417
COVER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
6G5538
COVER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
3J5167
COVER
129, D9G
129, D9G
2J7756
COVER
163
163
3K3763
COVER
955H
955H
3K7353
COVER
955H
955H
3K4121
COVER ASSEM
955H
955H
3K3024
COVER
955H
955H
4H9630
COVER ASSEM.
583H, D8H
583H, D8H
9H1256
COVER ASSEM.
583H, D8H
583H, D8H
5M4062
COVER ASSEM.
977H
977H
3K9694
COVER
955H
955H