COVER-SHAFT 7X5567 - Caterpillar

Illustration 13 g00101379 (1) Thickness of seven new friction discs and of eight new plates ... 52.56 1.34 mm (2.069 .053 inch)Note: The measurement must be made when the friction discs and the plates are compressed.Note: This dimension is only the thickness of seven new friction discs and of eight new plates. This dimension does not include the running clearance of the clutch pack.Running clearance for number seven clutch pack (Low Gear) ... 4.27 .52 mm (0.168 0.021 inch)Note: Refer to the procedure: Procedure to Measure Running ClearanceThickness of one new 6Y-7981 Friction Disc ... 4.32 0.10 mm (.170 .004 inch)Minimum allowable thickness for reusability ... 3.65 mm (.144 inch)Thickness of one new 3P-0337 Plate ... 2.79 0.08 mm (.109 .003 inch) (2) Thickness of six new friction discs and of five new plates ... 39.00 0.88 mm (1.530 .035 inch)Note: The measurement must be made when the friction discs and the plates are compressed.Note: This dimension is only the thickness of six new friction discs and five new plates. This dimension does not include the running clearance of the clutch pack.Running clearance for number eight clutch pack (High Gear) ... 1.91 .62 mm (0.075 0.024 inch)Note: Refer to the procedure: Procedure to Measure Running ClearanceThickness of one new 6I-8912 Friction Disc ... 4.00 0.08 mm (.157 .003 inch)Minimum allowable thickness for reusability ... 3.33 mm (.131 inch)Thickness of one new 110-7723 Plate ... 3.00 0.08 mm (.118 .003 inch) (4) 8M-4295 SpringTest length ... 26.9 mm (1.06 inch)Test force ... 74 6 N (16 1 lb)Free length after test ... 44.0 mm (1.75 inch)Outside diameter ... 15.2 mm (.60 inch) (5) 102-5881 Wave SpringTest length ... 38.2 mm (1.50 inch)Test force ... 2090 222 N (470 50 lb)Free length after test ... 50.0 mm (1.97 inch)Outside diameter ... 106.01 0.66 mm (4.174 .026 inch) (7) Torque for two bolts ... 55 10 N m (40 7 lb ft)
Illustration 14 g00101380
Detail A
(D) Install 5H-8985 Spring Pin (8) in 6Y-2425 Seal Carrier (6) with 6.5 mm (.26 inch) maximum protruding out of the carrier.
Illustration 15 g00101381
View (B)
( E) Installation depth for 9W-6467 Sleeve Bearings (3) in 6Y-2432 Gear Assembly (9) ... 0.5 0.5 mm (.02 .02 inch)Inside diameter of bearing after assembly ... 69.925 0.039 mm (2.7529 .0015 inch)Diameter of shaft in bearing area ... 69.842 0.008 mm (2.7497 .0003 inch)
Illustration 16 g00101382
Detail C
(F) ( G) Installation depth for 9W-6467 Sleeve Bearings (10) in 6Y-3858 Gear Assembly (11) ... 0.5 0.5 mm (.02 .02 inch)Inside diameter of bearing after assembly ... 69.925 0.039 (2.7529 .0015 inch)Diameter of shaft in bearing area ... 69.842 0.008 mm (2.7497 .0003 inch)Procedure to Measure Running Clearance
Illustration 17 g00101068
Typical Example
Use this procedure in order to check for proper clutch