8H0645 COVER Caterpillar parts
Rating:
Alternative (cross code) number:
CA8H0645
8H-0645
8H0645
CA8H0645
8H-0645
8H0645
Weight: 4 pounds 2 kg.
Cross Reference:
ACDelco
TP 542,
ALCO FILTER
MD-067,
MD-067M,
ASAS
AS 307,
BALDWIN
PF823,
PF8232,
PF8233,
PF8234,
PF8236,
PF823E,
PF824,
PF8242,
PF8292,
BOSCH
0 986 450 697,
CATERPILLAR
1R-0724,
1S-6811,
1Y-1827,
2W-2130,
4H-8792,
4H-8860,
4M-8641,
4S-5368,
5L-7534,
5L-7564,
5M-0473,
5M-0476,
5M-0953,
5S-5144,
6H-5931,
6H-5932,
7B-7635,
8H-0645,
8H-0671,
8H-0835,
8H-4825,
8M-5388,
8M-7828,
8M-7830,
8M-9641,
9H-1252,
9H-1353,
9H-4537,
9H-4565,
9H-4729,
9H-8792,
9L-0025,
CLEAN FILTERS
MG 054,
COOPERS
AZF 045,
G 528,
G 528 A,
G 528 B,
COOPERSFIAAM FILTERS
FA4249,
CROSLAND
488,
DONALDSON
P558792,
ELOFIC
EXF-435,
FIL FILTER
MF 120,
FLEETGUARD
FF116,
FRAD
45.65.04/30,
FRAM
C11661,
C11661PL,
C11662PL,
C11663PL,
C11664PL,
C1166PL,
GENERAL MOTORS
5574747,
5574787,
GUD FILTERS
G 528,
HENGST FILTER
E73KP,
KNECHT
EN 331,
LUBERFINER
364-F,
L 364-F,
L 364-F1,
LP 229,
MAHLE FILTER
KX 11,
MISFAT
F615,
P.B.R.
AG-1022,
PUROLATOR
EP 21,
RYCO
HDR2059P,
HDR2059PA,
SOFIMA
S 6615 N,
TECNOCAR
N1166,
TEHO
7128,
D 128,
UFI
26.615.00,
UNICO FILTER
FP 8160,
WIX FILTERS
33180,
33181,
33187,
33188,
33189,
33642,
WOODGATE
WGF116,
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the mounting bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
Illustration 1 g02191813
If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure. If the engine has a right-hand side oil filter, follow Step 2.a through Step 2.c in order to remove blanking plate (8).
Remove bolts (10).
Remove blanking plate (8).
Remove gasket (9) (not shown).
Remove bolt (1) from fuel injection line clamp (2). Position clamp (2) away from the engine oil cooler assembly.
Cut cable straps (3) from the engine wiring harness assembly.
Remove plastic tube assembly (4) from crankcase breather canister (5) and the plastic tube assembly clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Remove plastic tube assembly (12) from crankcase breather canister (5) and crankcase breather valve (11). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Remove bolt (7) from bracket (6). Position bracket (6) away from the engine oil cooler.
Illustration 2 g02191874
Do not remove bolts from Position (A).
Remove bolts (13) from engine oil cooler (14). Note: The bolts are different lengths. Note the position of the different bolts. Note the location and the orientation of the brackets for the tube assemblies.
Remove engine oil cooler assembly (14) from the cylinder block.
Remove gasket (15) (not shown) from engine oil cooler (14).
Illustration 3 g02191814
If necessary, follow Step 12.a through Step 12.c in order to disassembly the engine oil cooler.
Remove bolts (16) from engine oil cooler assembly (14).
Remove engine oil cooler matrix (19) from spacer plate (17).
Remove gasket (18).
Start By:
Remove the mounting bracket for the Electronic Control Module (ECM) . Refer to Disassembly and Assembly, "ECM Mounting Bracket- Remove and Install" for the correct procedure.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Drain" for the correct procedure.
Illustration 1 g02191813
If the engine has a left-hand side oil filter, remove the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install" for the correct procedure. If the engine has a right-hand side oil filter, follow Step 2.a through Step 2.c in order to remove blanking plate (8).
Remove bolts (10).
Remove blanking plate (8).
Remove gasket (9) (not shown).
Remove bolt (1) from fuel injection line clamp (2). Position clamp (2) away from the engine oil cooler assembly.
Cut cable straps (3) from the engine wiring harness assembly.
Remove plastic tube assembly (4) from crankcase breather canister (5) and the plastic tube assembly clips. Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Remove plastic tube assembly (12) from crankcase breather canister (5) and crankcase breather valve (11). Refer to Disassembly and Assembly, "Crankcase Breather- Remove" for the correct procedure.
Remove bolt (7) from bracket (6). Position bracket (6) away from the engine oil cooler.
Illustration 2 g02191874
Do not remove bolts from Position (A).
Remove bolts (13) from engine oil cooler (14). Note: The bolts are different lengths. Note the position of the different bolts. Note the location and the orientation of the brackets for the tube assemblies.
Remove engine oil cooler assembly (14) from the cylinder block.
Remove gasket (15) (not shown) from engine oil cooler (14).
Illustration 3 g02191814
If necessary, follow Step 12.a through Step 12.c in order to disassembly the engine oil cooler.
Remove bolts (16) from engine oil cooler assembly (14).
Remove engine oil cooler matrix (19) from spacer plate (17).
Remove gasket (18).
Parts cover Caterpillar catalog:
8G7111
COVER
Caterpillar
Caterpillar
8G6627
COVER
Caterpillar
Caterpillar
8G6457
COVER
Caterpillar
Caterpillar
8G6306
COVER
Caterpillar
Caterpillar
8G5683
COVER
Caterpillar
Caterpillar
8G3093
COVER
Caterpillar
Caterpillar
8H2997
COVER A.
Caterpillar
Caterpillar
8H2966
COVER
Caterpillar
Caterpillar
8H2456
COVER
Caterpillar
Caterpillar
8H2237
COVER A
Caterpillar
Caterpillar
8H1316
COVER A.-RAD.
Caterpillar
Caterpillar
8H1279
COVER
Caterpillar
Caterpillar