3264278 CRANKSHAFT AS Caterpillar parts
140H, 143H, 14H, 160H, 163H, 3176C, 345B, 345B II, 345B II MH, 345B L, 572R II, 65E, 725, 75E, 814F, 815F, 816F, 966G II, C-10, C-12, CPT372, D7R II, R1600G, R1700G, TK1051, W345B II
Rating:
Alternative (cross code) number:
CA3264278
326-4278
3264278
CA3264278
326-4278
3264278
Weight: 227 pounds 102 kg.
ARTICULATED TRUCK, WHEELED EXCAVATOR,
Related part:
3264278
CRANKSHAFT A-UTN
0R8195
R
3264278
CRANKSHAFT AS-YM
5241287
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
This part in 2 request:
Show.
This information for suppliers only!
2021-06-19
2018-02-07
Compatible equipment models: 3264278:
Information:
3606 (8RB),
3608 (6MC),
3612 (9RC),
3616 (1PD) EnginesDescription of Change: Improved "Woodward 2301A" Electronic Control Groups are used with the 3600 Family of Engines in generator set applications. The new control groups have internal changes that change the engine speed signal filter from 15 hertz to 7.5 hertz. This change improves the engine stability and does not affect engine response. Engine stability problems can cause other control system problems or torsional driveline failures.Adaptable To: The new control groups replace the former control groups as follows. The new 4P1561 Control Group replaces the former 9Y6982 Control Group.
The new 4P1570 Control Group replaces the former 7C7824 Control Group.
The new 4P1579 Control Group replaces the former 7W1444 Control Group.
The improved control groups are effective with 3600 Engines 8RB401, 6MC307, 9RC086, 1PD043.
If a new control group is installed, see the "Pre-Startup Instructions" and "After Startup Instructions".
Pre-Startup Instructions
The pre-startup potentiometer (pot) settings recommended in the "Woodward 2301A Manual" may be to responsive for some of the 3600 Family Of Engines in generator set applications. The following pot settings should be used as the pre-startup adjustment of the governor. The list of pot adjustments that follows is based on a scale of 0 to 10.
Set Gain Pot at 2
Set Reset Pot at 5
Set Compensation Pot at 0
Changes from these setting after startup should be made with caution.
After Startup Instructions
1. After the engine is started, warm the engine and coupling by adding load.2. Remove the load and check for stable operation at low and high idle. Watch for rapid motion of the actuator lever (about 5-10 Hz).3. Shut the engine down if the rapid actuator lever motion occurs. After shutting the engine down, either decrease the setting on the gain pot or increase slightly increase the setting on the reset pot. Then, repeat Steps 1 and 2. DO NOT set the compensation pot greater than 2 (0 is preferred). If the compensation pot setting is greater than 2, unstable operation may cause coupling damage. If misfire is detected, the engine should be shut down and the fuel system checked. Misfire can be detected by using individual exhaust temperature alarms. Set the alarms for activation when a cylinder is 50°C (122°F) lower than the mean temperature of the other cylinders.
3608 (6MC),
3612 (9RC),
3616 (1PD) EnginesDescription of Change: Improved "Woodward 2301A" Electronic Control Groups are used with the 3600 Family of Engines in generator set applications. The new control groups have internal changes that change the engine speed signal filter from 15 hertz to 7.5 hertz. This change improves the engine stability and does not affect engine response. Engine stability problems can cause other control system problems or torsional driveline failures.Adaptable To: The new control groups replace the former control groups as follows. The new 4P1561 Control Group replaces the former 9Y6982 Control Group.
The new 4P1570 Control Group replaces the former 7C7824 Control Group.
The new 4P1579 Control Group replaces the former 7W1444 Control Group.
The improved control groups are effective with 3600 Engines 8RB401, 6MC307, 9RC086, 1PD043.
If a new control group is installed, see the "Pre-Startup Instructions" and "After Startup Instructions".
Pre-Startup Instructions
The pre-startup potentiometer (pot) settings recommended in the "Woodward 2301A Manual" may be to responsive for some of the 3600 Family Of Engines in generator set applications. The following pot settings should be used as the pre-startup adjustment of the governor. The list of pot adjustments that follows is based on a scale of 0 to 10.
Set Gain Pot at 2
Set Reset Pot at 5
Set Compensation Pot at 0
Changes from these setting after startup should be made with caution.
After Startup Instructions
1. After the engine is started, warm the engine and coupling by adding load.2. Remove the load and check for stable operation at low and high idle. Watch for rapid motion of the actuator lever (about 5-10 Hz).3. Shut the engine down if the rapid actuator lever motion occurs. After shutting the engine down, either decrease the setting on the gain pot or increase slightly increase the setting on the reset pot. Then, repeat Steps 1 and 2. DO NOT set the compensation pot greater than 2 (0 is preferred). If the compensation pot setting is greater than 2, unstable operation may cause coupling damage. If misfire is detected, the engine should be shut down and the fuel system checked. Misfire can be detected by using individual exhaust temperature alarms. Set the alarms for activation when a cylinder is 50°C (122°F) lower than the mean temperature of the other cylinders.
Cat SIS web machinery list:
Parts crankshaft Caterpillar catalog:
1694188
CRANKSHAFT GP
814F, 815F, 816F, 966G II, C-10, C-12, TK1051
814F, 815F, 816F, 966G II, C-10, C-12, TK1051
1172743
CRANKSHAFT GP
3176C, 345B, 345B II, 345B II MH, 345B L, 480, 572R II, 65E, 75D, 75E, C-10, D7R II, R1600, R1600G, R1700G, W345B II
3176C, 345B, 345B II, 345B II MH, 345B L, 480, 572R II, 65E, 75D, 75E, C-10, D7R II, R1600, R1600G, R1700G, W345B II
1323212
CRANKSHAFT GP
16H, 730, C-12, C12, MTC835, SBF214, SUF557
16H, 730, C-12, C12, MTC835, SBF214, SUF557
1323210
CRANKSHAFT GP
140H, 143H, 14H, 160H, 163H, 725, C-10, CPT372
140H, 143H, 14H, 160H, 163H, 725, C-10, CPT372
1694190
CRANKSHAFT GP
972G II, C-12
972G II, C-12
3264280
CRANKSHAFT AS
16H, 3196, 365B, 365B II, 365B L, 730, 85E, 95E, 972G II, C-12, C12, MTC835, SBF214, SUF557
16H, 3196, 365B, 365B II, 365B L, 730, 85E, 95E, 972G II, C-12, C12, MTC835, SBF214, SUF557
1512920
CRANKSHAFT AS
3176C, 345B, 345B II, 345B II MH, 345B L, 65E, 75E, C-10, D7R II, W345B II
3176C, 345B, 345B II, 345B II MH, 345B L, 65E, 75E, C-10, D7R II, W345B II
1459976
CRANKSHAFT-COMPRESSOR
3176B, 3176C, 3196, C-10, C-12
3176B, 3176C, 3196, C-10, C-12
1175030
CRANKSHAFT-AIR COMPRESSOR
3406E, C-10, C-12
3406E, C-10, C-12
1512920
CRANKSHAFT AS
3176C, 345B, 345B II, 345B II MH, 345B L, 65E, 75E, C-10, D7R II, W345B II
3176C, 345B, 345B II, 345B II MH, 345B L, 65E, 75E, C-10, D7R II, W345B II
3264280
CRANKSHAFT AS
16H, 3196, 365B, 365B II, 365B L, 730, 85E, 95E, 972G II, C-12, C12, MTC835, SBF214, SUF557
16H, 3196, 365B, 365B II, 365B L, 730, 85E, 95E, 972G II, C-12, C12, MTC835, SBF214, SUF557
1694189
CRANKSHAFT AS
85D, 972G II, C-12
85D, 972G II, C-12
1694187
CRANKSHAFT AS
345B, 480, 75D, 966G II, D7R II, R1600, R1600G
345B, 480, 75D, 966G II, D7R II, R1600, R1600G
2715658
CRANKSHAFT AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 214B, 30/30, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 12M, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 160K, 214B, 30/30, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 3...
4P9857
CRANKSHAFT AS
330B, 350, 639D, 65C, 973, 973C, D6H, D6R, D7H, R1300
330B, 350, 639D, 65C, 973, 973C, D6H, D6R, D7H, R1300
1556632
CRANKSHAFT AS
651B, 834G, 836G, 988G, AD55, C-16, C16, MTC835
651B, 834G, 836G, 988G, AD55, C-16, C16, MTC835
2611544
CRANKSHAFT AS
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521...
12H, 140M, 140M 2, 160M, 160M 2, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521...
1397018
CRANKSHAFT GP
3054, 3054B, 312, 312C, 315, 317, 416C, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 554, 914G, CB-534B, CB-535B, CP-433C, CS-431C, IT14G, PS-300B
3054, 3054B, 312, 312C, 315, 317, 416C, 416D, 420D, 424D, 428D, 430D, 432D, 438D, 442D, 554, 914G, CB-534B, CB-535B, CP-433C, CS-431C, IT14G, PS-300B
3081852
CRANKSHAFT AS
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024, 3024C, 304.5, AP-255E, BB-621C, C1.5, C2.2, CB-334E, CB-34, CB34B, CB34B XW, CC34B
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3024, 3024C, 304.5, AP-255E, BB-621C, C1.5, C2.2, CB-334E, CB-34, CB34B, CB34B XW, CC34B
1526790
CRANKSHAFT GP
216, 228, 906
216, 228, 906
1731280
CRANKSHAFT GP
216, 236, 247, 248, 267, 287, 3034, 906
216, 236, 247, 248, 267, 287, 3034, 906