3436003 CRANKSHAFT Caterpillar parts
314E LCR, 416F, 432F, 434F, 444F, C4.4XQ80, CW-34
Rating:
Alternative (cross code) number:
CA3436003
343-6003
3436003
CA3436003
343-6003
3436003
Weight: 77 pounds 34 kg.
BACKHOE LOADER, PNEUMATIC COMPACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$686.42
05 May 2021
1.0[0.45] Pounds
US: MAGELLAN DISTRI
Hilti KWIK Bolt TZ Expansion Anchor - Carbon Steel - KB-TZ 1/2" x 4-1/2" - 3436003 - Box of 160
HILTI Especially Suited for Seismic and Cracked Concrete Applications || Seismic Qualifications Tested in Accordance with ACI 355.2 and ICC-ES AC193 || Small Minimum Edge Distance and Spacing for Maximum Design Flexibility || Nuts and Washers are Pre-Assembled || Rounded End for Easy Installation
HILTI Especially Suited for Seismic and Cracked Concrete Applications || Seismic Qualifications Tested in Accordance with ACI 355.2 and ICC-ES AC193 || Small Minimum Edge Distance and Spacing for Maximum Design Flexibility || Nuts and Washers are Pre-Assembled || Rounded End for Easy Installation
For full view, you need register
Compatible equipment models: 3436003:
Information:
Illustration 1 g01456250
Connections of the level switch for the autolube
This diagnostic code is associated with the level switch for the autolube. The switch is connected to two inputs of the ECM. One contact is open and the other contact is grounded during proper operation. This FMI 03 means that the ECM has determined that the normally open contact and the normally closed contact are open.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all of the connections in the circuit are clean and secure. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1022 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.
Table 1
Status of the Level Switch
Float Position Resistance
FULL 33 Ohms
EMPTY 243 Ohms Note: Check the resistance from contact 1 to contact 2 of the harness for the switch. If the resistance is within the range in Table 1 the switch is operating correctly.Test Step 1. CHECK THE OPERATION OF THE SWITCH
The machine harness remains disconnected from the switch.
Connect one lead from a multimeter to contact 1 of the harness connector on the switch.
Connect the other lead from a multimeter to contact 2 of the harness connector on the switch.
Measure the resistance between contact A and contact B . Note the resistance. Expected Result:The resistance from contact 1 to contact 2 is within the range in Table 1.Results:
YES - The resistance measurement is within the range. Proceed to Test Step 2.
NO - The resistance measurement is not within the range. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE HARNESS
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector from the pressure switch.
Measure the resistance between frame ground of the machine and contact 2 (wire 202-BK(Black)) of the machine harness connector for the switch. Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The circuit is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The circuit is open. The machine harness has failed.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE HARNESS
The disconnect switch and the key start switch remain in the OFF position.
The machine harness remains disconnected from the switch.
Disconnect the machine harness connector(s) from the ECM.
Measure the resistance between contacts J1-70 (wire 202-BK(Black)) and J1-22 (wire E985-BR(Brown)) of the machine harness to all the contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than
Parts crankshaft Caterpillar catalog:
3464197
CRANKSHAFT GP
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ80, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ80, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL
3558526
CRANKSHAFT GP
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ80, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 416F, 420F, 428F, 430F, 432F, 434F, 444F, 450F, C4.4, C4.4XQ80, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL
3895185
CRANKSHAFT AS
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
272D, 272D XHP, 299D, 299D XHP, 910K, 914K
2947922
CRANKSHAFT
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 246C, 252B, 256C, 262C, 267B, 268B, 272C, 277C, 287C, 297C, 3044C, 906, 906H, 907H, 908, 908H, C3.4
2497352
CRANKSHAFT AS
236B, 267B, 268B, 3044C, 906, C3.4
236B, 267B, 268B, 3044C, 906, C3.4
2258841
CRANKSHAFT GP
3054E, 315C, 432E, M313C, M315C, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
3054E, 315C, 432E, M313C, M315C, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
3180365
CRANKSHAFT GP
3054B, TH210, TH215
3054B, TH210, TH215
12G, 140G, 160H, 235, 3306, 3306B, 966C, 977L, D25C, D300B, D30C, D350C, D35C, D5, D6C, D6H, D7G
428, CB-424, CS-323, PR-75, PS-110, PS-130, PS-180, RT50
3764077
CRANKSHAFT
450F, C4.4, C4.4XQ100, CP-68B, CP-74B, CS-56B, CS-66B, CS-76B, CS-78B
450F, C4.4, C4.4XQ100, CP-68B, CP-74B, CS-56B, CS-66B, CS-76B, CS-78B
3879840
CRANKSHAFT AS
236D, 242D, 246D, 257D, 259D, 262D, 277D, 279D, 287D, 289D, 308E, 308E CR, 308E SR, 308E2 CR, 906H2, 907H2, 908H2
236D, 242D, 246D, 257D, 259D, 262D, 277D, 279D, 287D, 289D, 308E, 308E CR, 308E SR, 308E2 CR, 906H2, 907H2, 908H2
3764076
CRANKSHAFT
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 420F, 428F, 430F, 450F, C4.4, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, 420F, 428F, 430F, 450F, C4.4, CB-44B, CB-54B, CP-54B, CS-54B, CS-64B, CW-34, D3K2 LGP, D4K2 XL, D5K2 XL