AVSPARE.COM
parts catalog

CRANKSHAFT AS 3618847 - Caterpillar


3618847 CRANKSHAFT AS Caterpillar parts 3608, C280-8, G3608
Rating:
51
Alternative (cross code) number:
CA3618847
361-8847
3618847
Caterpillar 3618847 CRANKSHAFT AS
Weight: 5275 pounds 2392 kg.

Buy CRANKSHAFT AS 3618847 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE, MARINE ENGINE,

Compatible equipment models: 3618847:

GAS ENGINE  G3608  
MARINE ENGINE  3608   C280-8   Caterpillar
Number on catalog scheme:
  For full view, you need register

Information:


DANGER: Shock/Electrocution Hazard-Do not operate this equipment or work on this equipment unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings will result in serious injury or death.
Personal injury or death can result from high voltage.When power generation equipment must be in operation to make tests and/or adjustments, high voltage and current are present.Improper test equipment can fail and present a high voltage shock hazard to its user.Make sure the testing equipment is designed for and correctly operated for high voltage and current tests being made.When servicing or repairing electric power generation equipment:
Make sure the unit is off-line (disconnected from utility and/or other generators power service), and either locked out or tagged DO NOT OPERATE.
Remove all fuses.
Make sure the generator engine is stopped.
Make sure all batteries are disconnected.
Make sure all capacitors are discharged.Failure to do so could result in personal injury or death. Make sure residual voltage in the rotor, stator and the generator is discharged.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Grounding the Frame
In any generator set installation, the frame of the generator must be positively connected to an earth ground. This connection is the first connection that is made at the installation. This connection is the last connection that should be removed. If the generator set is on flexible mounting pads, the ground connection must be flexible in order to avoid possible breakage in later operation.Ground connection cable or straps should have at least the current carrying capacity of the largest line lead to the connected load. Joints in cables or straps must be clean, free of electrical resistance, and protected from possible oxidation. Bolted ground connection joints eventually oxidize. The joints are frequent sources of radio frequency interference (RFI). Joints that are silver soldered and bolted are preferred.Neutral Connections
The generators with a Wye Configuration usually have the neutral ground when the generator is installed. Grounding the neutral is for preventing damage to equipment.If the neutral wire is grounded and one of the phase leads becomes grounded, the excessive current will open a load circuit breaker. Also, the excessive current will cause the generator voltage to collapse. The result depends on the following items: electrical characteristics of the generator, type of fault and trip rating of the circuit breaker. An undervoltage device may be required in order to provide an adequate short circuit protection.There are some cases when the neutral wire is not grounded. An ungrounded generator neutral lead is acceptable when the possibility of grounds to the phase leads has been

Cat SIS web machinery list:

Caterpillar parts catalog
G3608 Petroleum XH700001-UP


Parts crankshaft Caterpillar catalog:

1935845 CRANKSHAFT AS
3608, C280-8, G3608, G3612
1935846 CRANKSHAFT GP
3608, C280-8, G3608
3618848 CRANKSHAFT GP
3608, C280-8, G3608
3224909 CRANKSHAFT GP
226B, 226B3, 232B, 242B, 247B, 247B3, 257B
3590939 CRANKSHAFT GP
3516, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, C175-16
1616928 CRANKSHAFT GP
3516B, 3516C, 789C, 793C, 793D, 994F, 994H, G3516E, PM3516
2342670 CRANKSHAFT GP
3054E, 315C, 432E, M313C, M315C, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.