4H5514 CRANKSHAFT BEARING REPLACEMENT GROUP Caterpillar parts
D342
Rating:
Alternative (cross code) number:
CA4H5514
4H-5514
4H5514
CA4H5514
4H-5514
4H5514
Weight: 0.80 pounds 0 kg.
INDUSTRIAL ENGINE,
Compatible equipment models: 4H5514:
Information:
Illustration 15 g06040501
Press the "OK" button to close the screen.Body and Avoidance Boundaries
To create Body and Avoidance Boundaries perform the following steps:
Key on machine and drive approximately 20 meters to obtain an accurate heading and position.
Park machine, apply parking brake and place wheel chock blocks. DO NOT TURN OFF MACHINE.
Illustration 16 g06041088
Illustration 17 g06041092
In Cat MineStar System office software, open the Site Editor window by navigating toMachine Tracking> Site Editorand thenSelect:"Create Rectangle"Then select: "Create Zone".
Illustration 18 g06041097
Move cursor on the Plan view to the general area where the zone is to be placed, then click to set the zone location:Name zone "machine_X_virtual_size"Note: X represents the machine number. (For example"machine_52_virtual_size")
Illustration 19 g06041103
Zoom in to a level where the zone can be created, the exact size and shape of the body boundary then drag the corners of the zone to the exact corners of the body boundary.
Double-click the new zone to open the Zone Editor.
Press the Apply button in the Zone Editor window.
Illustration 20 g06041107Note: The body boundary is indicated on the Plan view as a red dashed line around the machine.
Physically mark the location of the projected 4 corners of the machine (use stakes, cones, or other similar device to mark the corners of the machine on the ground.) These points are shown in the illustration 20as green dots.
Move the machine to a position away from the marked points (approximately 20-30 meters). Park and apply parking brake. Then take precautions to not disturb the marked corner locations.Note: The machine can be turned OFF at this point.Note: Obtain survey coordinates for the marked four corners of the machine body area.
Illustration 21 g06041114
Illustration 22 g06041116
In Cat MineStar System office software, open the Site Editor window by navigating to"Machine Tracking" >"Site Editor"and thenSelect:"Create Rectangle"Then select: "Create Zone".
Illustration 23 g06041119
Move cursor on the Plan view to the general area where the zone is to be placed, then click to set the zone location:Name zone "machine_X_virtual_size"Note: X represents the machine number. (For example "machine_52_virtual_size")
Illustration 24 g06349688
Double-click the new zone to open the Zone Editor.
On the General tab, set the "Zone Display Color"
Ensure that all options are unchecked.
Illustration 25 g06349692
Next click the Polygon tab.
Set Unit: Centimeter.Note: Only whole numbers are allowed.
Set corners for the zone to match the survey points taken earlier.
Illustration 26 g06041140
Press the Apply button in the Zone Editor window.
Illustration 27 g06041146
In Cat MineStar System office software, open the Site Monitor window.Machine Tracking >Site Monitor then Locate the new zone.Now verify that the "machine_X_virtual_size" zone completely covers the "machine_X_actual_size" zone.
Caterpillar SIS machinery equipment:
Parts crankshaft Caterpillar catalog:
7H6757
CRANKSHAFT BEARING REPLACEMENT GROUP
583H, D342, D342C, D8H
583H, D342, D342C, D8H
8M3477
CRANKSHAFT REPLACEMENT GEAR GROUP
583H, D342, D342C, D8H
583H, D342, D342C, D8H
1S7582
CRANKSHAFT BEARING REPLACEMENT GROUPS
D342, D342C, D8H
D342, D342C, D8H
1S7583
CRANKSHAFT BEARING REPLACEMENT GROUPS
D342, D342C, D8H
D342, D342C, D8H
1S7584
CRANKSHAFT BEARING REPLACEMENT GROUPS
D342, D342C, D8H
D342, D342C, D8H
3L8455
CRANKSHAFT
D342
D342
4S7436
CRANKSHAFT ASSEM.
D342, D342C, D8H, G342C
D342, D342C, D8H, G342C
8F3755
CRANKSHAFT ASSEM.
D326F, D337, D342, D397D
D326F, D337, D342, D397D
4H7032
CRANKSHAFT
D342
D342
8H5320
CRANKSHAFT
583H, D342, D342C, D8H
583H, D342, D342C, D8H
4M0447
CRANKSHAFT
D342, D342C, D8H
D342, D342C, D8H
2A3590
CRANKSHAFT GROUP
955C, D315
955C, D315
4253479
CRANKSHAFT GP
C140-16
C140-16
4350067
CRANKSHAFT GP-PUMP
WS223 SS, WSP273
WS223 SS, WSP273
4349989
CRANKSHAFT GP-PUMP
WS223 SS, WSP273
WS223 SS, WSP273
1S7583
CRANKSHAFT BEARING REPLACEMENT GROUPS
D342, D342C, D8H
D342, D342C, D8H
1S7582
CRANKSHAFT BEARING REPLACEMENT GROUPS
D342, D342C, D8H
D342, D342C, D8H
4L3367
CRANKSHAFT
D342C
D342C
8M3477
CRANKSHAFT REPLACEMENT GEAR GROUP
583H, D342, D342C, D8H
583H, D342, D342C, D8H
7H6757
CRANKSHAFT BEARING REPLACEMENT GROUP
583H, D342, D342C, D8H
583H, D342, D342C, D8H