AVSPARE.COM
parts catalog

CRANKSHAFT 4M0447 - Caterpillar


4M0447 CRANKSHAFT Caterpillar parts D342, D342C, D8H
Rating:
28
Alternative (cross code) number:
CA4M0447
4M-0447
4M0447
Caterpillar 4M0447 CRANKSHAFT
Weight: 413 pounds 187 kg.

Buy CRANKSHAFT 4M0447 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE, TRACK-TYPE TRACTOR,

Compatible equipment models: 4M0447:

INDUSTRIAL ENGINE  D342   D342C  
MARINE ENGINE  D342   D342C  
TRACK-TYPE TRACTOR  D8H   Caterpillar
Number on catalog scheme: None
  For full view, you need register

Information:


Illustration 2 g00728921
Note: The bucket should be level and the bucket should be under no pressure when the pin assemblies are removed.
Remove bolts (5) and washers (4) from the pin assemblies on each of the arm and bearing assemblies.
Illustration 3 g00728927
Install a suitable support under arm and bearing assembly (6) in order to support the arm and bearing assembly when the pin assemblies are removed.
Use Tooling (B) in order to remove all four collet assemblies (7) .
Illustration 4 g00728958
Illustration 5 g00532868
Loosen bolts (8) at the end of both arm and bearing assemblies (6) .
Use Tooling (C) in order to remove both pin assemblies (9) from the arm and bearing assemblies.
Illustration 6 g01019512
Attach a suitable lifting device in order to remove bucket (10) .
Remove the bucket. The weight of the standard bucket is 1680 kg (3704 lb).Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
D     5P-0960     Molybdenum Grease     1    
E     4C-5598     High Temperature Anti-Seize     1    
Illustration 7 g01019512
Attach a suitable lifting device in order to install bucket (10) .
Place the bucket into position. The weight of the standard bucket is approximately 1680 kg (3704 lb).
Illustration 8 g00728958
Note: Lubricate the lip seals in the arm and bearing assemblies. Lubricate the lip seals lightly with the lubricant that is being sealed. Coat the bores for the pin assemblies with Tooling (D) .
Install pin assemblies (9) in arm and bearing assemblies (6) with the filler plugs to the top. Verify that the pin assemblies and arm and bearing assemblies are in the center of the bosses on the bracket of the bucket. Tighten bolts (8) to a torque of 270 25 N m (199 18 lb ft).
Illustration 9 g00729016
Illustration 10 g00728921
Put Tooling (E) on the inside and outside diameters of collet assemblies (7). Install all four collet assemblies (7) .
Put Tooling (E) on the threads of bolts (5). Install Washers (4) and bolts (5) on the pin assemblies in each arm and bearing assembly. Tighten bolts (5) to a torque of 620 80 N m (457 59 lb ft). Hit the bolts with a hammer in order to reduce the torque on the bolts below 350 N m (258 lb ft). Tighten the bolts again to a torque of 620 80 N m (457 59 lb ft). Hit the bolts with a hammer again in order to reduce the torque on the bolts below 500 N m (369 lb ft). Tighten the bolts to a final torque of 620 80 N m (457 59 lb ft).
Illustration 11 g00728909
Note: Lubricate the lip seals in the lift link and bearing assembly. Lubricate the lip seals lightly with the lubricant that is being sealed. Coat the bores for the pin assembly with Tooling (D) .
Use a suitable lifting device in order to lift link and bearing assembly (1) into position. The weight of lift link and bearing assembly (1) is approximately 55 kg (120 lb). Install the spacer, the washer,

Caterpillar parts catalog:

Caterpillar parts catalog
D342 ENGINE 31B00001-02477
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A03860-04468 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A10725-24432 (MACHINE)
D8 TRACTOR / POWER SHIFT / 46A03044-10724 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A03860-04468 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A04469-05328 (MACHINE)
D8 TRACTOR / POWER SHIFT / 46A03044-10724 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)


Parts crankshaft Caterpillar catalog:

4S7436 CRANKSHAFT ASSEM.
D342, D342C, D8H, G342C
8F3755 CRANKSHAFT ASSEM.
D326F, D337, D342, D397D
8H5320 CRANKSHAFT
583H, D342, D342C, D8H
8H5320 CRANKSHAFT
583H, D342, D342C, D8H
4W8504 CRANKSHAFT PULLEY
3508, 3512, 3516, G3508, G3512, G3516
7W6472 CRANKSHAFT PULLEY
3508, 3508B, 3512, 3512B, 3516, 3516B, G3508, G3512, G3516, G3516B, G3520B
8M4505 CRANKSHAFT ASSEM.
955H, 955K, D330A, D4D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.