CRANKSHAFT GP 4P9948 - Caterpillar

Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed. The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, filters, and the installation of new components due to normal wear and aging. The performance of this product may be diminished if proper maintenance intervals and procedures are not followed. Components may experience accelerated wear if proper maintenance intervals and procedures are not followed.Note: Use whichever of the following that occurs first in order to determine the maintenance intervals: fuel consumption , service hours and calendar time . Before each consecutive interval is performed, all maintenance from the previous intervals must be performed.Products that operate in severe operating conditions may require more frequent maintenance.When Required
Battery or Battery Cable - Disconnect
Engine - Clean
Engine Oil Level Gauge - Calibrate
Engine Storage Procedure - Check
Fuel System - Prime
Heat Exchanger - Inspect
Maintenance Recommendations
Sea Water Strainer - Clean/Inspect
Zinc Rods - Inspect/Replace
Daily
Closed Crankcase Ventilation (CCV) Filter Service Indicator - Inspect
Cooling System Coolant Level - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Walk-Around Inspection
Initial 20 to 40 Service Hours
Belts - Inspect/Adjust/Replace
Every 50 Service Hours or Weekly
Aftercooler Condensate Drain Valve - Inspect/Clean
Sea Water Strainer - Clean/Inspect
Zinc Rods - Inspect/Replace
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Cooling System Coolant Sample (Level 2) - Obtain
Every 500 Service Hours
Cooling System Coolant Sample (Level 1) - Obtain
Every Year
Cooling System Coolant Sample (Level 2) - Obtain
Every 6000 Service Hours or 3 Years
Cooling System Coolant Extender (ELC) - Add
Every 12 000 Service Hours or 6 Years
Cooling System Coolant (ELC) - Change
First 14 400 L (3750 US gal) of Fuel or 250 Service Hours
Engine Valve Lash - Inspect/Adjust
Fuel Injector - Inspect/Adjust
Every 14 400 L (3750 US gal) of Fuel or 250 Service Hours or 1 Year
Belts - Inspect/Adjust/Replace
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine - Clean
Engine Air Cleaner Element - Clean/Replace
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Every 57 000 L (15 000 US gal) of Fuel or 1000 Service Hours
Aftercooler Core - Clean/Test
Closed Crankcase Ventilation (CCV) Fumes Disposal Filter - Replace
Heat Exchanger - Inspect
Turbocharger - Inspect
Every 170 400 L (45 000 US gal) of Fuel or 3000 Service Hours
Auxiliary Water Pump (Bronze Impeller) - Inspect
Cooling System Coolant (DEAC) - Change
Cooling System Water Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine Crankcase Breather - Clean
Engine Mounts - Inspect
Engine Speed/Timing Sensor - Clean/Inspect
Engine Valve Lash - Inspect/Adjust
Engine Valve Rotators - Inspect
Fuel Injector - Inspect/Adjust
Starting Motor - Inspect
Every 284 000 L (75 000 US gal) of Fuel or 5000 Service Hours
Alternator - Inspect
Maintenance Recommendations
Overhaul (Top End)
Water Pump - Inspect
Every 570 000 L (150 000 US gal) of Fuel or 10 000 Service Hours
Maintenance Recommendations
Overhaul (Major)