1077553 CROWN AS-PISTON Caterpillar parts
3114, 3116
Rating:
Alternative (cross code) number:
CA1077553
107-7553
1077553
CA1077553
107-7553
1077553
Weight: 3 pounds 1 kg.
TRUCK ENGINE,
Related part:
1077553
PISTON GP-PACK
0R9888
R
You can buy:
US$76.56
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CARTEX Crown Piston 1077553 for FITS Caterpillar CAT 3114 3116 Truck Engine in USA
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
Piston 1077553 Fit Intended For 3114 3116 Truck Engine
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts
Generic Machinery Parts || Heavy Equipment Parts || Spare Parts
Number on catalog scheme:
1
For full view, you need register
Information:
Remove And Install Crankshaft Main Bearings
preparatory step: a) remove oil pump 1. Remove the No. 2 and No. 6 crankshaft main bearing caps.2. Using tool (A), remove the upper halves of main bearings by rotating the crankshaft and rolling the bearing out of cylinder block. Remove lower halves of main bearings from the caps.3. Lubricate the bearing surfaces of upper halves of main bearings with clean SAE 30 engine oil. Using tool (A), roll upper halves of main bearings into place.4. Clean the main bearing caps, and install lower halves of bearings in caps.5. Using wire (B), check the bearing clearance. Install caps and tighten both retaining bolts to 30 3 lb. ft. (4,1 0,4 mkg), mark both heads and bearing caps, then tighten each bolt an additional 90° from mark. Remove the bearing caps and measure thickness of wire. Main bearing clearance should be .0030-.0059 in. (0,076-0,150 mm).6. Lubricate threads of cap retaining bolts, face of washers, and lower halves of main bearings with clean SAE 30 engine oil. Position caps on engine with number stamped on cap facing, the corresponding number stamped on face on left side of cylinder block. Install retaining bolts and washers. Tighten both bolts to 30 3 lb. ft. (4,1 0,4 mkg), mark both bolt heads and bearing caps, then tighten both bolts an additional 90° from mark7. Remove the No. 1,3,4,5, and 7 main bearing caps. Remove the crankshaft thrust bearings (1). Lubricate the new thrust bearings with clean SAE 30 engine oil, and install them in cylinder block with groove in bearing toward crankshaft.8. Repeat Step 2 through Step 6 for remaining bearings. Check crankshaft end play using indicator group (C). End play should be .0025 - .0145 in. (0,064 - 0,368 mm). Maximum permissible end play is .025 in. (0,64 mm).concluding step: a) install oil pump
preparatory step: a) remove oil pump 1. Remove the No. 2 and No. 6 crankshaft main bearing caps.2. Using tool (A), remove the upper halves of main bearings by rotating the crankshaft and rolling the bearing out of cylinder block. Remove lower halves of main bearings from the caps.3. Lubricate the bearing surfaces of upper halves of main bearings with clean SAE 30 engine oil. Using tool (A), roll upper halves of main bearings into place.4. Clean the main bearing caps, and install lower halves of bearings in caps.5. Using wire (B), check the bearing clearance. Install caps and tighten both retaining bolts to 30 3 lb. ft. (4,1 0,4 mkg), mark both heads and bearing caps, then tighten each bolt an additional 90° from mark. Remove the bearing caps and measure thickness of wire. Main bearing clearance should be .0030-.0059 in. (0,076-0,150 mm).6. Lubricate threads of cap retaining bolts, face of washers, and lower halves of main bearings with clean SAE 30 engine oil. Position caps on engine with number stamped on cap facing, the corresponding number stamped on face on left side of cylinder block. Install retaining bolts and washers. Tighten both bolts to 30 3 lb. ft. (4,1 0,4 mkg), mark both bolt heads and bearing caps, then tighten both bolts an additional 90° from mark7. Remove the No. 1,3,4,5, and 7 main bearing caps. Remove the crankshaft thrust bearings (1). Lubricate the new thrust bearings with clean SAE 30 engine oil, and install them in cylinder block with groove in bearing toward crankshaft.8. Repeat Step 2 through Step 6 for remaining bearings. Check crankshaft end play using indicator group (C). End play should be .0025 - .0145 in. (0,064 - 0,368 mm). Maximum permissible end play is .025 in. (0,64 mm).concluding step: a) install oil pump
Caterpillar parts catalog:
Parts crown Caterpillar catalog:
3406E
3406E
3176, G3508
3116, 325, 325 LN, 613C II, 950F
3406E
3406E, R2900
