7E6875 CROWN AS-PISTON Caterpillar parts
3176
Rating:
Alternative (cross code) number:
CA7E6875
7E-6875
7E6875
CA7E6875
7E-6875
7E6875
Weight: 4 pounds 2 kg.
TRUCK ENGINE,
Compatible equipment models: 7E6875:
Number on catalog scheme:
1
For full view, you need register
Information:
Illustration 7 g01333301
Install spring (21) on clutch housing assembly (11) .
Illustration 8 g01333300
Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) . Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on Tooling (B) .
Illustration 10 g01208920
Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
Position cover assembly (8) onto clutch housing assembly (11) .Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates and discs in the clutch assembly.
Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or cleaning fluids contact the sealing surface.
Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
Position cover assembly (8) on the opposite side.
Install O-ring seal (10) on cover assembly (8) .
Illustration 15 g01208914
Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a minimum torque of 18 N m (13 lb ft) up to a maximum torque of 31 N m (23 lb ft).
Illustration 16 g02092935
Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling (F) .
Illustration 17 g01333295
Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N m (450 lb ft) up to a maximum torque of 750 N m (550 lb ft). After achieving the torque range, overtighten retainer (4) as needed in order to align the next position for locking screws (3) .
Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N m (62 lb in) to a maximum torque of 10 N m (89 lb in).
Illustration 19 g01208862
Position sensor (1) . Install bolt (2) .End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Caterpillar parts catalog:
Parts crown Caterpillar catalog:
3116, 325, 325 LN, 613C II, 950F
3114, 3116, 325, 325 LN, 950F, 950F II, 960F
16G, 30/30, 517, 527, 528, 528B, 530B, 615, 615C, 916, 920, D4H, D4H XL, D4HTSK II, D4HTSK III, D5M, D6R, D6R II, D7R, D7R II, D8N, DEUCE, FB518
120G, 12G, 130G, 14G, 30/30, 315C, 315D L, 3P, 3S, 4S, 508, 517, 613C, 637D, 657E, 910, 931, 931B, 933, 936, 936F, 939, 950B, 950F, D3B, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4E, D4E SR, D...
140M, 140M 2, 160M, 160M 2, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 637D, 973C, 973D, C9, CX31-C9I, D6R, D6R III, D6T, D7R XR, M330D, TH31-E61
140M, 160M, 2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D MH, 336D, 336D L, 336D LN, 340D L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, 586C, 627G, 637D, 637E, 637G, 814F...
3114, 3116
3406E
3406E
3176, G3508