AVSPARE.COM
parts catalog

CUP ASSEM. 2H9990 - Caterpillar



2H9990 CUP ASSEM. Caterpillar parts 977D, D337, D342, D342C, D353C, D8H, D9E, G342C CUP
Rating:
35
Alternative (cross code) number:
CA2H9990
2H-9990
2H9990
Caterpillar 2H9990 CUP ASSEM.
Weight: 0.94 pounds 0 kg.

Buy CUP ASSEM. 2H9990 Caterpillar genuine, new aftermarket tractor parts with delivery
GAS ENGINE, TRACK-TYPE TRACTOR,

Compatible equipment models: 2H9990:

GAS ENGINE  G342C  
INDUSTRIAL ENGINE  D342   D342C   D353C  
MARINE ENGINE  D337   D342  
TRACK LOADER  977D  
TRACK-TYPE TRACTOR  D8H   D9E   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:

2. Remove the bolt and retainer (9) (not shown) that hold pin (6) for the rod end of the tilt cylinder to the blade. Remove pin (6). Slide the rod end of tilt cylinder (8) from the blade and remove spacers (7) from each side. Push the tilt cylinder clear of the blade. Cap (11) and bolts (10) can not be removed until the blade is removed from the C-frame.3. Remove bolts (10) from the C-frame. Remove the blade. The weight is 320 Kg (700 lb.). 4. Remove cap (11), shims and bolts (10) from the blade (12). The following steps are for installation of the angling blade group.5. Fasten a hoist to the blade. 6. Put bolts (10) and cap (11) in position on the blade as shown without shims. 7. Put the blade in position and install the four bolts that hold the cap and blade to the C-frame. Tighten the bolts evenly. Measure the gap between cap (11) and C-frame (13). Remove bolts (10) from the C-frame. Install shims between cap (11) and C-frame (13) equal to the gap measured, plus one shim.8. Put blade (12) in position and install bolts (10) that hold cap (11), shims and blade (12) to the C-frame (13). Tighten the bolts in number sequence shown to a torque of 205 14 N m (150 10 lb.ft.). Turn the bolts 120° more.9. Put spacers (7) on each side of the rod end of the tilt cylinder and slide the rod end of tilt cylinder (8) into position on the blade with the spacer.10. Install pin (6) that holds the rod end of the tilt cylinder to the blade. Install the retainer and bolt (9), (not shown) that hold pin (6) for the rod end of the tilt cylinder in place.11. Put spacers (4) on each side of the rod end of the angling cylinders. Put angling cylinders (5) in position in the blade. Install pins (3) that hold the rod end of the angling cylinder in the blade. Install retainers (2) and the bolts (1) that hold pins (3) for the rod end of the angling cylinders in the blade.12. Remove the hoist.

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455
D342 MARINE ENGINE 32B00001-01539
D337 MARINE ENGINE 23B00300-00455
D342 ENGINE 31B00001-02477
D353 ENGINE 46B00001-00598
D342 ENGINE 31B00001-02477
D342 MARINE ENGINE 32B00001-01539
D342 MARINE ENGINE 32B01540-UP
D342 & G342 ENGINE 31B02478-03984
D353 ENGINE 46B00001-00598
D353 ENGINE 46B00599-00808
D342 & G342 ENGINE 31B02478-03984
D342 ENGINE 49B00001-01090
D342 & G342 ENGINE 31B02478-03984
D342 ENGINE 49B00001-01090
D342 & G342 ENGINE 31B02478-03984
G342 ENGINE 71B00001-UP
D342 & G342 ENGINE 31B02478-03984
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)
583 PIPELAYER 38A00001-00078 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
D8 TRACTOR / POWER SHIFT / 46A03044-10724 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)
583 PIPELAYER 38A00001-00078 (MACHINE)
D8H TRACTOR / POWER SHIFT / 46A00001-03043 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
D9 TRACTOR 50A00001-00212 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A00001-03859 (MACHINE)
D8 TRACTOR / POWER SHIFT / 46A03044-10724 (MACHINE)
D8 TRACTOR / DIRECT DRIVE / 36A03860-04468 (MACHINE)


Parts cup Caterpillar catalog:

8H7803 CUP-BEARING
621, 623, 627, 657, 657B, 666, 725, 725C, 730, 730C, 735, 735B, 740, 740B, CX31, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX31-P600, CX35, CX35-C18I, CX35-P800, D250E II, D300E II, D350E II, D400E I...
4B8393 CUP
530B, 621, 621B, 621E, 621F, 621G, 621H, 621K, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 631E, 631G, 633C, 633E II, 637D, 637E, 637G, 639D, 657,...
1B3942 CUP
245, 594, 594H, 630A, 650B, 666, 988B, D9E, D9G, D9H
1M7911 CUP-BEARING
561C, 583T, 587R, 587T, 951B, 955C, 955H, 955K, 977D, D5, D6C, D8N, D8R, D8R II, D8T, PL83, PL87, PM-201, PM-465, PM-565B
8H0901 CUP-BEARING
583H, 583K, 824C, 953, 953B, 980, 980B, 980C, 980F, 980F II, 994, 994D, 994F, 994H, AD40, AE40, D35C, D40D, D44B, D550B, D6T LGP, D8H, D8K, R1700 II, TS180, TS185, TS220, TS225
1B3934 CUP
583H, 583K, 613, 613C, 613C II, 613G, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824K, 825K, 826K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972...
1B3918 CUP
977D, D7F, RR-250
7B4956 CUP
561B, 977D
1B3937 CUP-BEARING
16G, 16H, 16H NA, 16M, 824C, 980, 980B, 980C, 980F, 994H, D35C, D35HP, D40D, D44B, D550B, D9E
4H3167 CUP
D364, D397D
4H1761 CUP
D326F, D337
4H1764 CUP
D326F, D337
2H0929 CUP
14E, 215, 215B, 215C, D364
2H6036 CUP
D337F, D342, D353C, D397D, D9E
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.