AVSPARE.COM
parts catalog

CUSHION A. 2H9086 - Caterpillar



2H9086 CUSHION A. Caterpillar parts CUSHION
Rating:
26
Alternative (cross code) number:
CA2H9086
2H-9086
2H9086
Caterpillar 2H9086 CUSHION A.

Buy CUSHION A. 2H9086 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 6 g01256218
Front View Of The Windshield (B) Right side (D) Left side
Illustration 7 g01256220
Detail G From Illustration 6 (B) Right side (J) 4I-0420 Strip
Illustration 8 g01256221
Detail H From Illustration 6 (B) Right side (K) 185-8221 Stop
Make sure that strip (J) and stop (K) are installed on the windshield frame. Install a new 4I-0420 Strip and a new 185-8221 Stop, if necessary. The locations of the strip and the stop are shown in Illustration 6, 7, and 8.
Illustration 9 g01256239
Windshield Frame And Switch (B) Right side (E) 117-6306 Switch (L) Windshield frame
Illustration 10 g01256241
Windshield Frame In Contact With The Switch (B) Right side (L) Windshield frame
Make sure that the switch contacts the windshield frame. Adjust the position of switch (E) and the bracket, if necessary. Refer to Illustration 9 and Illustration 10.
Illustration 11 g01256308
Activation of the switch (E) 117-6306 Switch
Make sure that the switch operates correctly. Press the switch with your finger. Proceed to Step 4 if the switch operates correctly. Troubleshoot the switch if the switch does not operate correctly.
Illustration 12 g01256309
Spring in the switch (E) 117-6306 Switch
Make sure that the spring in the switch operates correctly. Install a new 117-6306 Switch if the spring does not work correctly.
Illustration 13 g01256394
Wiring Harness (E) 117-6306 Switch
Make sure that the connection between the switch and the wiring harness is assembled securely.
Make sure that the ground circuit for the wiring harness is complete.
Make sure that the wiring harness is operating correctly. Check the controller if a new wiring harness is installed.
Make sure that the motor for the wiper is operating correctly.
Illustration 14 g01256617
Pulling The Windshield Inward
Pull the right hand top portion of the windshield inward while the wiper is operating. Refer to Illustration 14. Proceed to Step 5 if the wiper discontinues operation.
Check the surface of the 4I-0420 Strip. The strip should not be abrasive. Refer to Illustration 7 for the location of the strip. Install a new strip, if necessary.
Illustration 15 g01256634
Adjustment Of The Stop (K) 185-8221 Stop
Adjust the 185-8221 Stop that is mounted on the windshield frame. Use a counterclockwise rotation in order to adjust the stop. Rotate the stop for approximately one revolution.
Illustration 16 g01256637
Adjustment To The Weather Strip (M) Windshield seal
Adjust the position of the center striker and the weather strip. Make sure that the windshield will open and close properly.
Install an additional 4I-0420 Strip on the existing strip, if necessary.
Use water and perform a leak test in order to make sure that the seals are not leaking.


Parts cushion Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.